Includes questions types found on actual exam such as drag and drop, simulation, type in, and fill in the blank.
Service Provider Routing and Switching, Specialist (JNCIS-SP) JN0-364 Practice Test 13
Question 120
For fictional Stonebridge ISP, identify the shortcut that fails to address: Two intended Level 1 IS-IS peers on the same fiber have healthy Ethernet connectivity but cannot establish a Level 1 adjacency.
Change only IS-IS interface metric values while leaving the Level 1 NET area mismatch.
Configure an OSPF-style BDR requirement as though it were part of IS-IS.
Suppress all packet-loss alarms while retaining inconsistent adjacency timing.
Assume every IS-IS TLV has the same length and carries only an IPv4 route.
Explanation
Correct Answer
A:
The proposed shortcut undermines the expected result: show isis adjacency reports an Up Level 1 peer and the intended area routes appear. The safer implementation step is: Align NET area membership for Level 1 adjacency according to the provider topology plan.
Incorrect Answers
B:
This shortcut would also be unsafe, but for a different IS-IS DIS election case (A technician sees only one designated intermediate system listed on a multiaccess IS-IS LAN and assumes a backup DIS must also be elected.). It does not repeat the defect in this question: The router NET area addresses differ, so the peers cannot share the required Level 1 area.
C:
The proposal recreates the separate IS-IS hello holdtime mismatch error. The current case instead concerns: Two intended Level 1 IS-IS peers on the same fiber have healthy Ethernet connectivity but cannot establish a Level 1 adjacency. Its specific failed assumption is: The router NET area addresses differ, so the peers cannot share the required Level 1 area.
D:
This alternative is problematic for IS-IS TLV interpretation, rather than the reported IS-IS NET area mismatch. Corrective action here is: Align NET area membership for Level 1 adjacency according to the provider topology plan.
Question 121
At fictional Cobalt Datacenter (data center interconnect), this Junos network defect is reported: Operators expect two Level 2 routers in different IS-IS areas to peer, but a teammate proposes giving them identical area IDs. What should the specialist change first?
Inspect IS-IS Hello and hold-time settings plus loss and latency, then restore a stable supported transport or timer design.
Verify both interfaces support Level 2 and correct protocol reachability rather than needlessly merging area identifiers.
Inspect show route protocol isis and the intended forwarding table, including hidden or inactive route reasons.
Apply an explicit policy permitting the intended routes and rejecting the laboratory prefix before advertisement.
Explanation
Correct Answer
B:
This response addresses the specific IS-IS Level 2 interarea adjacency failure at Cobalt Datacenter. Apply: Verify both interfaces support Level 2 and correct protocol reachability rather than needlessly merging area identifiers. Its acceptance test is: The Level 2 adjacency reaches Up across different intended areas and backbone routes are exchanged.
Incorrect Answers
A:
That action would address the separate IS-IS hello holdtime mismatch case, where An IS-IS peer periodically times out after a high-latency transport path was inserted between two provider routers. The present IS-IS Level 2 interarea adjacency issue instead requires: Verify both interfaces support Level 2 and correct protocol reachability rather than needlessly merging area identifiers.
C:
Although relevant to IS-IS SPF route installation, this configuration does not remedy the reported IS-IS Level 2 interarea adjacency failure. Use: Verify both interfaces support Level 2 and correct protocol reachability rather than needlessly merging area identifiers.
D:
That action would address the separate IS-IS policy route export case, where A boundary router leaks a laboratory prefix into the provider IS-IS domain despite an approved limited export scope. The present IS-IS Level 2 interarea adjacency issue instead requires: Verify both interfaces support Level 2 and correct protocol reachability rather than needlessly merging area identifiers.
Question 122
A Junos routing specialist investigates at fictional Cobalt Datacenter: Operators expect two Level 2 routers in different IS-IS areas to peer, but a teammate proposes giving them identical area IDs. What control gap requires attention?
The operational inspection is directed at the wrong routing protocol and cannot reveal IS-IS adjacency state.
Configured IS-IS link metrics do not reflect the intended provider path cost policy.
Level 2 adjacency does not require a shared IS-IS area address; the relevant issue is interface level capability and transport compatibility.
IS-IS elects a DIS for a LAN pseudonode and does not use the OSPF DR and BDR election model.
Explanation
Correct Answer
C:
The scenario is explained by: Level 2 adjacency does not require a shared IS-IS area address; the relevant issue is interface level capability and transport compatibility. This is distinct from unrelated application failures. The recommended correction is: Verify both interfaces support Level 2 and correct protocol reachability rather than needlessly merging area identifiers.
Incorrect Answers
A:
The alternate cause would explain IS-IS adjacency command selection. For IS-IS Level 2 interarea adjacency at Cobalt Datacenter, the evidence instead supports: Level 2 adjacency does not require a shared IS-IS area address; the relevant issue is interface level capability and transport compatibility.
B:
This is a different failure mechanism: Configured IS-IS link metrics do not reflect the intended provider path cost policy. The current symptom is: Operators expect two Level 2 routers in different IS-IS areas to peer, but a teammate proposes giving them identical area IDs. The more direct defect is: Level 2 adjacency does not require a shared IS-IS area address; the relevant issue is interface level capability and transport compatibility.
D:
The alternate cause would explain IS-IS DIS election. For IS-IS Level 2 interarea adjacency at Cobalt Datacenter, the evidence instead supports: Level 2 adjacency does not require a shared IS-IS area address; the relevant issue is interface level capability and transport compatibility.
Question 123
Following remediation at fictional Cobalt Datacenter, how should the team verify that this specific issue is resolved? Operators expect two Level 2 routers in different IS-IS areas to peer, but a teammate proposes giving them identical area IDs.
Route selection prefers the terrestrial path under normal conditions and falls back on failure.
The Level 2 adjacency reaches Up across different intended areas and backbone routes are exchanged.
show isis adjacency reports an Up Level 1 peer and the intended area routes appear.
The adjacency remains Up across the tested transport condition and hold timers no longer expire prematurely.
Explanation
Correct Answer
B:
The acceptance criterion must prove the original behavior changed: The Level 2 adjacency reaches Up across different intended areas and backbone routes are exchanged. This follows from the remedial action: Verify both interfaces support Level 2 and correct protocol reachability rather than needlessly merging area identifiers.
Incorrect Answers
A:
The alternative proof tests a different cause: Configured IS-IS link metrics do not reflect the intended provider path cost policy. The relevant acceptance condition remains: The Level 2 adjacency reaches Up across different intended areas and backbone routes are exchanged.
C:
This observation is appropriate for IS-IS NET area mismatch, not the IS-IS Level 2 interarea adjacency defect at Cobalt Datacenter. Verify instead: The Level 2 adjacency reaches Up across different intended areas and backbone routes are exchanged.
D:
The alternative proof tests a different cause: The IS-IS neighbor hold-time behavior cannot tolerate the observed Hello delivery pattern on the transport. The relevant acceptance condition remains: The Level 2 adjacency reaches Up across different intended areas and backbone routes are exchanged.
Question 124
After corrective implementation at fictional Cobalt Datacenter, reviewers revisit: Operators expect two Level 2 routers in different IS-IS areas to peer, but a teammate proposes giving them identical area IDs. Which safeguard best protects the repaired state?
Retest this approved Junos service-provider routing and switching control after relevant changes: show isis adjacency displays the agreed Level 1 or Level 2 adjacency as Up.
Retest this approved Junos service-provider routing and switching control after relevant changes: The decoded LSP distinguishes each supported TLV and correctly presents intended prefixes or attributes.
Retest this approved Junos service-provider routing and switching control after relevant changes: show route advertising-protocol isis output excludes the lab prefix and includes sanctioned exports.
Retest this approved Junos service-provider routing and switching control after relevant changes: The Level 2 adjacency reaches Up across different intended areas and backbone routes are exchanged.
Explanation
Correct Answer
D:
The repeated release test must confirm: The Level 2 adjacency reaches Up across different intended areas and backbone routes are exchanged. That check detects recurrence of the original defect: Level 2 adjacency does not require a shared IS-IS area address; the relevant issue is interface level capability and transport compatibility.
Incorrect Answers
A:
This recurring check measures IS-IS circuit-level mismatch, whereas the fixed IS-IS Level 2 interarea adjacency behavior needs ongoing evidence that: The Level 2 adjacency reaches Up across different intended areas and backbone routes are exchanged.
B:
That control would prevent the different failure IS-IS uses TLVs to encode diverse information, so the decoder ignores fields or misreads their lengths. It would not detect recurrence of: Level 2 adjacency does not require a shared IS-IS area address; the relevant issue is interface level capability and transport compatibility.
C:
The proposed check belongs to the separate IS-IS policy route export issue at Orion Transit. For this case, retest: The Level 2 adjacency reaches Up across different intended areas and backbone routes are exchanged.
Question 125
For fictional Cobalt Datacenter, identify the shortcut that fails to address: Operators expect two Level 2 routers in different IS-IS areas to peer, but a teammate proposes giving them identical area IDs.
Increase DIS priority despite the fact that the two peers have no common circuit level.
Adjust Ethernet speed labels without inspecting the IS-IS metric used by SPF.
Suppress all packet-loss alarms while retaining inconsistent adjacency timing.
Readdress both independently managed IS-IS areas as one without checking Level 2 circuit settings.
Explanation
Correct Answer
D:
Reject this option for the observed incident at Cobalt Datacenter: Operators expect two Level 2 routers in different IS-IS areas to peer, but a teammate proposes giving them identical area IDs. Use instead: Verify both interfaces support Level 2 and correct protocol reachability rather than needlessly merging area identifiers.
Incorrect Answers
A:
The proposal recreates the separate IS-IS circuit-level mismatch error. The current case instead concerns: Operators expect two Level 2 routers in different IS-IS areas to peer, but a teammate proposes giving them identical area IDs. Its specific failed assumption is: Level 2 adjacency does not require a shared IS-IS area address; the relevant issue is interface level capability and transport compatibility.
B:
This alternative is problematic for IS-IS metric traffic engineering, rather than the reported IS-IS Level 2 interarea adjacency. Corrective action here is: Verify both interfaces support Level 2 and correct protocol reachability rather than needlessly merging area identifiers.
C:
This shortcut would also be unsafe, but for a different IS-IS hello holdtime mismatch case (An IS-IS peer periodically times out after a high-latency transport path was inserted between two provider routers.). It does not repeat the defect in this question: Level 2 adjacency does not require a shared IS-IS area address; the relevant issue is interface level capability and transport compatibility.
Question 126
At fictional Ridgeway Wireless (wireless aggregation), this Junos network defect is reported: One circuit participates only in Level 1 on the remote router and only in Level 2 on the local router, preventing an adjacency. What should the specialist change first?
Compare cumulative IS-IS metrics and set approved interface values for the intended primary and standby paths.
Add and verify the loopback's appropriate IS-IS reachability without creating an unnecessary physical neighbor on loopback.
Inspect show route protocol isis and the intended forwarding table, including hidden or inactive route reasons.
Configure a mutually supported level on the intended link and verify the corresponding adjacency output.
Explanation
Correct Answer
D:
Correct because the observable problem is: One circuit participates only in Level 1 on the remote router and only in Level 2 on the local router, preventing an adjacency. Use the controlled remedy: Configure a mutually supported level on the intended link and verify the corresponding adjacency output. Confirm the resulting state with: show isis adjacency displays the agreed Level 1 or Level 2 adjacency as Up.
Incorrect Answers
A:
Although relevant to IS-IS metric traffic engineering, this configuration does not remedy the reported IS-IS circuit-level mismatch failure. Use: Configure a mutually supported level on the intended link and verify the corresponding adjacency output.
B:
That action would address the separate IS-IS passive loopback case, where An IS-IS loopback prefix is missing after deployment because the internal router loopback was omitted from the protocol scope. The present IS-IS circuit-level mismatch issue instead requires: Configure a mutually supported level on the intended link and verify the corresponding adjacency output.
C:
The proposal is a correction for IS-IS SPF route installation, not this situation: One circuit participates only in Level 1 on the remote router and only in Level 2 on the local router, preventing an adjacency. Here the cause is: The enabled IS-IS circuit levels have no common level for an adjacency to form.
Question 127
A Junos routing specialist investigates at fictional Ridgeway Wireless: One circuit participates only in Level 1 on the remote router and only in Level 2 on the local router, preventing an adjacency. What control gap requires attention?
The topology database must reconcile LSP sequence number, lifetime, flooding and current originator state.
IS-IS elects a DIS for a LAN pseudonode and does not use the OSPF DR and BDR election model.
The LSDB can be healthy while route preference, next-hop eligibility or table context prevents FIB installation.
The enabled IS-IS circuit levels have no common level for an adjacency to form.
Explanation
Correct Answer
D:
The scenario is explained by: The enabled IS-IS circuit levels have no common level for an adjacency to form. This is distinct from unrelated application failures. The recommended correction is: Configure a mutually supported level on the intended link and verify the corresponding adjacency output.
Incorrect Answers
A:
That diagnosis belongs to IS-IS LSP freshness, for example: A link is decommissioned but a core router displays stale topology information from an older IS-IS LSP sequence. It does not explain this case, which is caused by: The enabled IS-IS circuit levels have no common level for an adjacency to form.
B:
The alternate cause would explain IS-IS DIS election. For IS-IS circuit-level mismatch at Ridgeway Wireless, the evidence instead supports: The enabled IS-IS circuit levels have no common level for an adjacency to form.
C:
This is a different failure mechanism: The LSDB can be healthy while route preference, next-hop eligibility or table context prevents FIB installation. The current symptom is: One circuit participates only in Level 1 on the remote router and only in Level 2 on the local router, preventing an adjacency. The more direct defect is: The enabled IS-IS circuit levels have no common level for an adjacency to form.
Question 128
Following remediation at fictional Ridgeway Wireless, how should the team verify that this specific issue is resolved? One circuit participates only in Level 1 on the remote router and only in Level 2 on the local router, preventing an adjacency.
show isis adjacency displays the agreed Level 1 or Level 2 adjacency as Up.
The troubleshooting record names the IS-IS interface, peer system ID, level, and Up or Down state.
The expected active DIS originates the LAN pseudonode LSP and a new DIS is elected if it fails.
The adjacency remains Up across the tested transport condition and hold timers no longer expire prematurely.
Explanation
Correct Answer
A:
This outcome directly measures IS-IS circuit-level mismatch: show isis adjacency displays the agreed Level 1 or Level 2 adjacency as Up. It tests the diagnosed issue: The enabled IS-IS circuit levels have no common level for an adjacency to form.
Incorrect Answers
B:
The alternative proof tests a different cause: The operational inspection is directed at the wrong routing protocol and cannot reveal IS-IS adjacency state. The relevant acceptance condition remains: show isis adjacency displays the agreed Level 1 or Level 2 adjacency as Up.
C:
That result would validate the separate IS-IS DIS election scenario (A technician sees only one designated intermediate system listed on a multiaccess IS-IS LAN and assumes a backup DIS must also be elected.). It does not prove the needed IS-IS circuit-level mismatch outcome: show isis adjacency displays the agreed Level 1 or Level 2 adjacency as Up.
D:
This observation is appropriate for IS-IS hello holdtime mismatch, not the IS-IS circuit-level mismatch defect at Ridgeway Wireless. Verify instead: show isis adjacency displays the agreed Level 1 or Level 2 adjacency as Up.
Question 129
After corrective implementation at fictional Ridgeway Wireless, reviewers revisit: One circuit participates only in Level 1 on the remote router and only in Level 2 on the local router, preventing an adjacency. Which safeguard best protects the repaired state?
Retest this approved Junos service-provider routing and switching control after relevant changes: The Level 2 adjacency reaches Up across different intended areas and backbone routes are exchanged.
Retest this approved Junos service-provider routing and switching control after relevant changes: show isis adjacency reports an Up Level 1 peer and the intended area routes appear.
Retest this approved Junos service-provider routing and switching control after relevant changes: The decoded LSP distinguishes each supported TLV and correctly presents intended prefixes or attributes.
Retest this approved Junos service-provider routing and switching control after relevant changes: show isis adjacency displays the agreed Level 1 or Level 2 adjacency as Up.
Explanation
Correct Answer
D:
This periodic check is appropriate because it examines the exact prior failure at Ridgeway Wireless: show isis adjacency displays the agreed Level 1 or Level 2 adjacency as Up.
Incorrect Answers
A:
The proposed check belongs to the separate IS-IS Level 2 interarea adjacency issue at Cobalt Datacenter. For this case, retest: show isis adjacency displays the agreed Level 1 or Level 2 adjacency as Up.
B:
This recurring check measures IS-IS NET area mismatch, whereas the fixed IS-IS circuit-level mismatch behavior needs ongoing evidence that: show isis adjacency displays the agreed Level 1 or Level 2 adjacency as Up.
C:
That control would prevent the different failure IS-IS uses TLVs to encode diverse information, so the decoder ignores fields or misreads their lengths. It would not detect recurrence of: The enabled IS-IS circuit levels have no common level for an adjacency to form.
Question 130
For fictional Ridgeway Wireless, identify the shortcut that fails to address: One circuit participates only in Level 1 on the remote router and only in Level 2 on the local router, preventing an adjacency.
Suppress all packet-loss alarms while retaining inconsistent adjacency timing.
Repeatedly clear the IS-IS adjacency without determining why the computed route was not installed.
Increase DIS priority despite the fact that the two peers have no common circuit level.
Reset BGP sessions because the OSPF neighbor list is empty on an IS-IS-only link.
Explanation
Correct Answer
C:
The proposed shortcut undermines the expected result: show isis adjacency displays the agreed Level 1 or Level 2 adjacency as Up. The safer implementation step is: Configure a mutually supported level on the intended link and verify the corresponding adjacency output.
Incorrect Answers
A:
This shortcut would also be unsafe, but for a different IS-IS hello holdtime mismatch case (An IS-IS peer periodically times out after a high-latency transport path was inserted between two provider routers.). It does not repeat the defect in this question: The enabled IS-IS circuit levels have no common level for an adjacency to form.
B:
The proposal recreates the separate IS-IS SPF route installation error. The current case instead concerns: One circuit participates only in Level 1 on the remote router and only in Level 2 on the local router, preventing an adjacency. Its specific failed assumption is: The enabled IS-IS circuit levels have no common level for an adjacency to form.
D:
This shortcut would also be unsafe, but for a different IS-IS adjacency command selection case (A junior engineer searches only show ospf neighbor when an IS-IS underlay loses a peer during maintenance.). It does not repeat the defect in this question: The enabled IS-IS circuit levels have no common level for an adjacency to form.
Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-364) Practice Tests
Our team works hard to provide students with high exam practice test questions and compelling learning experiences. We're confident of the quality level of the products we offer and provide no hassle satisfaction guarantee.
Why choose Exam-Labs?613,682+Satisfied Customers since 2015
100% Latest Exam Questions
Accurate & Updated Answers
Regular Free Updates
24/7 Customer Support
Instant Download
Exam Info
Juniper JN0-364 Practice Test Questions, Juniper JN0-364 Exam Practice Test Questions
Looking to pass your tests the first time. You can study with Juniper JN0-364 certification practice test questions and answers, study guide, training courses. With Exam-Labs VCE files you can prepare with Juniper JN0-364 Service Provider Routing and Switching, Specialist (JNCIS-SP) exam practice test questions and answers. The most complete solution for passing with Juniper certification JN0-364 exam practice test questions and answers, study guide, training course.
JN0-364 Service Provider Routing and Switching, Specialist
JN0-364 is the current Service Provider Routing and Switching, Specialist exam as of October 2026. HPE Juniper Networking lists 65 multiple-choice questions in 90 minutes, Pearson VUE delivery, JNCIA-Junos as the prerequisite, and Junos OS 25.2 as the software reference. It replaced JN0-363 on February 2, 2026.
The blueprint is broad: protocol-independent routing, OSPF, IS-IS, BGP, Layer 2 bridging and VLANs, spanning-tree variants, MPLS, IPv6, GRE tunnels, and high availability. The common thread is service-provider operations. Candidates must understand not only what each protocol does but how state is configured, verified, and troubleshot across a Junos network.
The current JN0-106 associate exam provides the Junos foundation. If routing tables, policy, interface hierarchy, or operational mode are still slow, strengthen those first. JN0-364 adds enough simultaneous control planes that weak fundamentals become a major study bottleneck.
Protocol-independent routing is the control surface beneath the protocols
The blueprint includes static, aggregate, and generated routes, martian addresses, routing instances, RIB groups, load balancing, and filter-based forwarding. These are not secondary topics. They determine which tables routes enter, which paths become active, and how traffic can be steered independently of the dynamic protocol that learned a prefix.
Build labs where the same destination appears from multiple sources. Change route preference, create an aggregate, move information between routing instances, and apply filter-based forwarding. Before running a show command, predict which route should be active and why. That habit turns the routing table into a reasoned outcome rather than a display to memorize.
The concepts behind static routing make a clean baseline because they isolate local route selection before dynamic signaling complicates the picture.
OSPF and IS-IS should be practiced as living topology databases
For OSPF, JN0-364 expects knowledge of the link-state database, packet types, router IDs, neighbors, DR/BDR roles, area and router types, LSAs, configuration, policy, and troubleshooting. For IS-IS, candidates need PDUs, TLVs, levels, areas, adjacencies, DIS behavior, metrics, policy, and operational verification.
Do not study those items as vocabulary lists. Form a neighbor, inspect the database, change a metric, remove a link, and watch the shortest-path result change. Repeat the topology with the other protocol. This makes the shared link-state model visible while preserving the differences in hierarchy and protocol behavior.
The detailed explanation of OSPF areas and LSAs is useful, but a service-provider candidate should be equally comfortable reading IS-IS adjacency and database state.
BGP should be verified at every stage between peer and forwarding table
JN0-364 covers BGP messages, attributes, route selection, IBGP/EBGP interaction, peers, options, policy, and troubleshooting. A disciplined verification sequence is essential: confirm transport and session state, inspect received routes, apply policy reasoning, verify next-hop resolution, inspect active routes, and check what is advertised onward.
Create at least one lab where the BGP session remains Established while the desired route disappears. Use import policy, an unreachable next hop, or a competing path. The exercise proves why “peer up” and “service working” are different statements. The broader mechanics of BGP path selection become easier to apply when every attribute change produces visible route-state evidence.
Service-provider BGP work is inseparable from policy. Spend time writing and reading policy terms so that you can explain exactly why a route is accepted, rejected, modified, or exported.
Provider switching topics protect the service edge
The Layer 2 domain includes service-provider switching platforms, bridging concepts, frame processing, virtual switches, Q-in-Q provider bridging, VLAN port modes, tagging, IRB, and spanning-tree variants. These topics matter because service-provider networks often carry customer Layer 2 services even when the core itself is highly routed.
Practice Q-in-Q by distinguishing customer tags from the service-provider tag. Then verify how the frame is handled at ingress, across the provider domain, and at egress. This makes the separation between customer segmentation and provider forwarding explicit.
Spanning tree should be understood with security controls such as BPDU, loop, and root protection. Those features encode expectations at the edge and help prevent customer or access faults from destabilizing a larger Layer 2 domain.
MPLS study should begin with packet forwarding before signaling
The current blueprint includes MPLS terminology, label headers, end-to-end forwarding, label information, routing-table relationships, RSVP, LDP, and segment routing with MPLS. Start with the dataplane. Trace how an ingress node pushes a label, how transit nodes swap it, and how the egress processes the final label.
Then attach each signaling method to the label-switched path it creates. LDP distributes labels along routing paths, RSVP can establish traffic-engineered paths, and segment routing expresses path intent through segments. The concepts in MPLS forwarding provide a strong base when paired with Junos route and label-table output.
Do not memorize labels as static numbers. Focus on the control information that creates them and the forwarding behavior they enable. That perspective scales into VPN and traffic-engineering work at the professional level.
When comparing MPLS control methods, keep one question in view: what information tells the router which labeled path to use? LDP generally couples label distribution to IGP reachability, RSVP can signal traffic-engineered LSPs with explicit constraints, and segment routing represents path intent through ordered segments. Practice reading the resulting state rather than memorizing a feature table. If an LSP is down, determine whether the missing evidence is an IGP route, a signaling relationship, a label binding, or the forwarding entry itself.
Troubleshooting should therefore move from dependency to dependent feature. Verify core addressing and IGP reachability first, then protocol sessions, then label or tunnel state, and finally end-to-end service traffic. This sequence is efficient because later layers cannot be healthy when their transport assumptions are false. It also mirrors real service-provider operations, where the fastest resolution often comes from proving the lowest broken dependency before touching policy or service configuration.
IPv6 belongs in the same routing model as IPv4
JN0-364 covers IPv6 static routing and dynamic routing through OSPFv3, IS-IS, and BGP, plus IPv6-over-IPv4 tunneling. Treat IPv6 as a routed protocol with its own addressing and neighbor behavior rather than as a separate specialty. Route selection, policy, protocol adjacency, and troubleshooting discipline still apply.
Build dual-stack labs so you can compare the same topology under both address families. Verify that a protocol session can be healthy for one family while reachability for another is absent. This teaches you to inspect family-specific route state instead of assuming that one working path proves the other.
For transition tunnels, explicitly trace the outer IPv4 path and the inner IPv6 packet. The layered model is the same one used for GRE and prevents confusion about which address family is failing.
GRE tunnels add reachability without removing underlay dependencies
The tunnel objective covers applications, design considerations, GRE configuration, and troubleshooting. A GRE interface can make two remote networks appear directly connected at the logical layer, but the outer endpoints still depend on ordinary routing. If the underlay cannot reach the tunnel destination, the overlay path cannot work.
In the lab, verify outer routes, tunnel source and destination, inner routing, and MTU. Then break each independently. The difference between an underlay failure and an inner-route problem becomes obvious when you compare packet captures and interface state.
Use the conceptual discussion of GRE tunneling to broaden understanding, while keeping configuration practice aligned to the exact JN0-364 objectives.
High availability combines fast detection with preserved forwarding
Current HA topics include LAG, graceful restart, GRES, NSB, NSR, BFD, and VRRP. Each protects a different part of service continuity. Link aggregation addresses physical path loss, BFD accelerates failure detection, graceful and nonstop mechanisms reduce control-plane disruption, and VRRP protects the first-hop gateway identity.
Build a table that states for each feature what fails, what detects the failure, what state is preserved, and what alternate path or node takes over. The principles of VRRP redundancy are especially useful when contrasted with BFD: one provides a virtual gateway role, the other supplies rapid liveness information.
In testing, record packets lost and convergence time. A protocol can be “working as designed” while still failing a service-level objective if recovery is too slow for the application.
Study the current exam as one service-provider system
Separate notebooks for OSPF, BGP, MPLS, and HA are useful early, but final preparation should combine them. Build a topology where an IGP supplies core reachability, MPLS uses that underlay, BGP carries service or external routes, and HA mechanisms protect critical paths. Then introduce a fault and decide which control plane should react.
Use the objective list as a four-part readiness matrix: explain, configure, verify, troubleshoot. If you can define a feature but cannot identify healthy operational output, the topic is incomplete. If you can configure it but cannot predict the effect of a failure, it is not yet specialist-level knowledge.
The current professional progression represented in the approved inventory is JN0-664. That path rewards candidates who build durable service-provider reasoning now, because advanced Layer 2 VPN, EVPN, MPLS, and policy work assumes the specialist foundation is already fluent.
Before scheduling, verify the live JN0-364 blueprint and software reference again. The certification program's branding changed under HPE Networking in September 2026, but the exam remains centered on Junos service-provider routing and switching. Use current first-party objectives for scope and let hands-on operational evidence—routes, adjacencies, labels, policy results, tunnel state, and failover behavior—drive the final review.
Use Juniper JN0-364 certification exam practice test questions, study guide and training course - the complete package at discounted price. Pass with JN0-364 Service Provider Routing and Switching, Specialist (JNCIS-SP) practice test questions and answers, study guide, complete training course especially formatted in VCE files. Latest Juniper certification JN0-364 exam practice test questions and answers will guarantee your success without studying for endless hours.
FAQs
Juniper JN0-364 Exam Practice Test Questions, Juniper JN0-364 Practice Test Questions and Answers
Do you have questions about our JN0-364 Service Provider Routing and Switching, Specialist (JNCIS-SP) practice test questions and answers or any of our products? If you are not clear about our Juniper JN0-364 exam practice test questions, you can read the FAQ below.
The JN0-364 Premium File has been developed by industry professionals, who have been working with IT certifications for years and have close ties with IT certification vendors and holders - with most recent exam questions and valid answers.
JN0-364 Premium File is presented in VCE format. VCE (Virtual CertExam) is a file format that realistically simulates JN0-364 exam environment, allowing for the most convenient exam preparation you can get - in the convenience of your own home or on the go. If you have ever seen IT exam simulations, chances are, they were in the VCE format.
What is VCE?
VCE is a file format associated with Visual CertExam Software. This format and software are widely used for creating tests for IT certifications. To create and open VCE files, you will need to purchase, download and install VCE Exam Simulator on your computer.
Can I try it for free?
Yes, you can. Look through free VCE files section and download any file you choose absolutely free.
Where do I get VCE Exam Simulator?
VCE Exam Simulator can be purchased from its developer, https://www.avanset.com. Please note that Exam-Labs does not sell or support this software. Should you have any questions or concerns about using this product, please contact Avanset support team directly.
How are Premium VCE files different from Free VCE files?
Premium VCE files have been developed by industry professionals, who have been working with IT certifications for years and have close ties with IT certification vendors and holders - with most recent exam questions and some insider information.
Free VCE files All files are sent by Exam-labs community members. We encourage everyone who has recently taken an exam and/or has come across some braindumps that have turned out to be true to share this information with the community by creating and sending VCE files. We don't say that these free VCEs sent by our members aren't reliable (experience shows that they are). But you should use your critical thinking as to what you download and memorize.
How long will I receive updates for JN0-364 Premium VCE File that I purchased?
Free updates are available during 30 days after you purchased Premium VCE file. After 30 days the file will become unavailable.
How can I get the products after purchase?
All products are available for download immediately from your Member's Area. Once you have made the payment, you will be transferred to Member's Area where you can login and download the products you have purchased to your PC or another device.
Will I be able to renew my products when they expire?
Yes, when the 30 days of your product validity are over, you have the option of renewing your expired products with a 30% discount. This can be done in your Member's Area.
Please note that you will not be able to use the product after it has expired if you don't renew it.
How often are the questions updated?
We always try to provide the latest pool of questions, Updates in the questions depend on the changes in actual pool of questions by different vendors. As soon as we know about the change in the exam question pool we try our best to update the products as fast as possible.
What is a Study Guide?
Study Guides available on Exam-Labs are built by industry professionals who have been working with IT certifications for years. Study Guides offer full coverage on exam objectives in a systematic approach. Study Guides are very useful for fresh applicants and provides background knowledge about preparation of exams.
How can I open a Study Guide?
Any study guide can be opened by an official Acrobat by Adobe or any other reader application you use.
What is a Training Course?
Training Courses we offer on Exam-Labs in video format are created and managed by IT professionals. The foundation of each course are its lectures, which can include videos, slides and text. In addition, authors can add resources and various types of practice activities, as a way to enhance the learning experience of students.
Enter Your Email Address to Proceed
Please fill out your email address below in order to purchase Certification/Exam.
Enter Your Email Address to Proceed
Please fill out your email address below in order to purchase Demo.
How It Works
Step 1. Choose Exam on Exam-Labs
Download IT Exams Questions & Answers
Step 2. Open Exam with Avanset Exam Simulator
Press here to download VCE Exam Simulator that simulates latest exam environment