Pass Juniper JN0-364 Exam in First Attempt Easily

Latest Juniper JN0-364 Practice Test Questions, Exam Dumps
Accurate & Verified Answers As Experienced in the Actual Test!

You save
$6.00
Save
Verified by experts
JN0-364 Questions & Answers
Exam Code: JN0-364
Exam Name: Service Provider Routing and Switching, Specialist (JNCIS-SP)
Certification Provider: Juniper
JN0-364 Premium File
69 Questions & Answers
Last Update: Nov 4, 2026
Includes questions types found on actual exam such as drag and drop, simulation, type in, and fill in the blank.
Verified by experts
JN0-364 Questions & Answers
Exam Code: JN0-364
Exam Name: Service Provider Routing and Switching, Specialist (JNCIS-SP)
Certification Provider: Juniper
JN0-364 Premium File
69 Questions & Answers
Last Update: Nov 4, 2026
Includes questions types found on actual exam such as drag and drop, simulation, type in, and fill in the blank.
$65.99
$59.99

Service Provider Routing and Switching, Specialist (JNCIS-SP) JN0-364 Practice Test 11

Question 100

For fictional Northline Metro, identify the shortcut that fails to address: Two valid OSPF paths exist to a shared service subnet but the router consistently selects an expensive backup link.

  1. Modify BGP local preference to change an OSPF-only route decision.
  2. Set both interfaces to unauthenticated operation to avoid troubleshooting the mismatched key.
  3. Disable OSPF authentication and assume incompatible timers will be ignored.
  4. Disable all routing policy and export every direct route to satisfy reachability.

Explanation

Correct Answer

A:

That shortcut preserves the original OSPF cost path preference weakness: The cumulative OSPF cost values make the backup path more attractive than the planned primary path. The controlled alternative is: Check per-interface OSPF metrics and the calculated route cost, then set design-approved costs.

Incorrect Answers

B:

The proposal recreates the separate OSPF area authentication mismatch error. The current case instead concerns: Two valid OSPF paths exist to a shared service subnet but the router consistently selects an expensive backup link. Its specific failed assumption is: The cumulative OSPF cost values make the backup path more attractive than the planned primary path.

C:

This alternative is problematic for OSPF hello dead-interval disagreement, rather than the reported OSPF cost path preference. Corrective action here is: Check per-interface OSPF metrics and the calculated route cost, then set design-approved costs.

D:

This shortcut would also be unsafe, but for a different OSPF route policy export case (A provider edge redistributes selected connected customer prefixes into OSPF but an unrelated management subnet is also advertised.). It does not repeat the defect in this question: The cumulative OSPF cost values make the backup path more attractive than the planned primary path.

Question 101

At fictional Meridian Fiber (metro aggregation), this Junos network defect is reported: An access area was configured as stub to limit external LSAs but an engineer expects external AS-external route entries inside that area. What should the specialist change first?

  1. Validate the stub area design and its ABR-supplied default route rather than forcing external LSAs into the stub.
  2. Compare and align the permitted OSPF hello and dead intervals on both ends of the link.
  3. Compare interface MTU and database exchange symptoms, then align the supported MTU design on both ends.
  4. Assign a unique stable router ID to each participant and perform a controlled adjacency refresh.

Explanation

Correct Answer

A:

This response addresses the specific OSPF stub area external reachability failure at Meridian Fiber. Apply: Validate the stub area design and its ABR-supplied default route rather than forcing external LSAs into the stub. Its acceptance test is: Access routers route permitted external destinations via the expected ABR default without individual AS-external LSAs.

Incorrect Answers

B:

Although relevant to OSPF hello dead-interval disagreement, this configuration does not remedy the reported OSPF stub area external reachability failure. Use: Validate the stub area design and its ABR-supplied default route rather than forcing external LSAs into the stub.

C:

That action would address the separate OSPF MTU exchange problem case, where An OSPF peer pair discovers one another but remains in database exchange after replacing an uplink with unequal MTU settings. The present OSPF stub area external reachability issue instead requires: Validate the stub area design and its ABR-supplied default route rather than forcing external LSAs into the stub.

D:

The proposal is a correction for OSPF router ID duplication, not this situation: An access area was configured as stub to limit external LSAs but an engineer expects external AS-external route entries inside that area. Here the cause is: The area type intentionally restricts external LSAs and a suitable default-route design is required for external destinations.

Question 102

A Junos routing specialist investigates at fictional Meridian Fiber: An access area was configured as stub to limit external LSAs but an engineer expects external AS-external route entries inside that area. What control gap requires attention?

  1. The observed neighbor states reflect normal DR and BDR adjacency behavior on a broadcast network, not necessarily a failure.
  2. The OSPF authentication parameters and keys are inconsistent between the adjacent interfaces.
  3. The expected link-state advertisement has not been originated or synchronized as intended for the target area.
  4. The area type intentionally restricts external LSAs and a suitable default-route design is required for external destinations.

Explanation

Correct Answer

D:

Fictional Meridian Fiber demonstrates this underlying defect: The area type intentionally restricts external LSAs and a suitable default-route design is required for external destinations. Validate after remediation by checking: Access routers route permitted external destinations via the expected ABR default without individual AS-external LSAs.

Incorrect Answers

A:

This is a different failure mechanism: The observed neighbor states reflect normal DR and BDR adjacency behavior on a broadcast network, not necessarily a failure. The current symptom is: An access area was configured as stub to limit external LSAs but an engineer expects external AS-external route entries inside that area. The more direct defect is: The area type intentionally restricts external LSAs and a suitable default-route design is required for external destinations.

B:

That diagnosis belongs to OSPF area authentication mismatch, for example: An OSPF adjacency stops forming just after an authentication key rotation on only one routing device. It does not explain this case, which is caused by: The area type intentionally restricts external LSAs and a suitable default-route design is required for external destinations.

C:

The alternate cause would explain OSPF LSA database divergence. For OSPF stub area external reachability at Meridian Fiber, the evidence instead supports: The area type intentionally restricts external LSAs and a suitable default-route design is required for external destinations.

Question 103

Following remediation at fictional Meridian Fiber, how should the team verify that this specific issue is resolved? An access area was configured as stub to limit external LSAs but an engineer expects external AS-external route entries inside that area.

  1. The transit router forms its expected OSPF adjacency and the loopback continues to be advertised without an unnecessary neighbor.
  2. Operational logs demonstrate whether neighbor state, LSDB advertisement, or route installation is the failure stage.
  3. Access routers route permitted external destinations via the expected ABR default without individual AS-external LSAs.
  4. show ospf neighbor reports the correct peer in the expected adjacency state on the shared interface.

Explanation

Correct Answer

C:

Sign-off requires case-specific evidence: Access routers route permitted external destinations via the expected ABR default without individual AS-external LSAs. Without that observation, the area type intentionally restricts external lsas and a suitable default-route design is required for external destinations.

Incorrect Answers

A:

That result would validate the separate OSPF passive-loopback interface scenario (A transit interface accidentally inherits passive behavior, leaving its intended adjacent router absent although local OSPF routes are present.). It does not prove the needed OSPF stub area external reachability outcome: Access routers route permitted external destinations via the expected ABR default without individual AS-external LSAs.

B:

This observation is appropriate for OSPF neighbor verification workflow, not the OSPF stub area external reachability defect at Meridian Fiber. Verify instead: Access routers route permitted external destinations via the expected ABR default without individual AS-external LSAs.

D:

That result would validate the separate OSPF area mismatch scenario (A pair of Junos routers can ping directly connected addresses but their OSPF neighbor table remains empty after enabling OSPF on the link.). It does not prove the needed OSPF stub area external reachability outcome: Access routers route permitted external destinations via the expected ABR default without individual AS-external LSAs.

Question 104

After corrective implementation at fictional Meridian Fiber, reviewers revisit: An access area was configured as stub to limit external LSAs but an engineer expects external AS-external route entries inside that area. Which safeguard best protects the repaired state?

  1. Retest this approved Junos service-provider routing and switching control after relevant changes: Only the designated customer prefixes appear in OSPF advertisements and the management subnet remains absent.
  2. Retest this approved Junos service-provider routing and switching control after relevant changes: Access routers route permitted external destinations via the expected ABR default without individual AS-external LSAs.
  3. Retest this approved Junos service-provider routing and switching control after relevant changes: The peers exchange compatible Hellos and their OSPF neighbor adjacency converges to the expected state.
  4. Retest this approved Junos service-provider routing and switching control after relevant changes: OSPF neighbor inspection identifies distinct router IDs and stable route computation after the refresh.

Explanation

Correct Answer

B:

This periodic check is appropriate because it examines the exact prior failure at Meridian Fiber: Access routers route permitted external destinations via the expected ABR default without individual AS-external LSAs.

Incorrect Answers

A:

That control would prevent the different failure The OSPF export policy matches a broader route set than the agreed service prefixes. It would not detect recurrence of: The area type intentionally restricts external LSAs and a suitable default-route design is required for external destinations.

C:

This recurring check measures OSPF hello dead-interval disagreement, whereas the fixed OSPF stub area external reachability behavior needs ongoing evidence that: Access routers route permitted external destinations via the expected ABR default without individual AS-external LSAs.

D:

That control would prevent the different failure The OSPF routers share a router identifier that should uniquely identify each OSPF speaker. It would not detect recurrence of: The area type intentionally restricts external LSAs and a suitable default-route design is required for external destinations.

Question 105

For fictional Meridian Fiber, identify the shortcut that fails to address: An access area was configured as stub to limit external LSAs but an engineer expects external AS-external route entries inside that area.

  1. Increase OSPF interface priority while leaving area membership inconsistent.
  2. Suppress all database checks permanently to mask the differing link MTUs.
  3. Force every pair on a shared Ethernet segment to Full by disabling the designated-router concept.
  4. Convert every access area to a backbone area solely to expose external link-state entries.

Explanation

Correct Answer

D:

The proposed shortcut undermines the expected result: Access routers route permitted external destinations via the expected ABR default without individual AS-external LSAs. The safer implementation step is: Validate the stub area design and its ABR-supplied default route rather than forcing external LSAs into the stub.

Incorrect Answers

A:

This alternative is problematic for OSPF area mismatch, rather than the reported OSPF stub area external reachability. Corrective action here is: Validate the stub area design and its ABR-supplied default route rather than forcing external LSAs into the stub.

B:

This shortcut would also be unsafe, but for a different OSPF MTU exchange problem case (An OSPF peer pair discovers one another but remains in database exchange after replacing an uplink with unequal MTU settings.). It does not repeat the defect in this question: The area type intentionally restricts external LSAs and a suitable default-route design is required for external destinations.

C:

The proposal recreates the separate OSPF broadcast DR election error. The current case instead concerns: An access area was configured as stub to limit external LSAs but an engineer expects external AS-external route entries inside that area. Its specific failed assumption is: The area type intentionally restricts external LSAs and a suitable default-route design is required for external destinations.

Question 106

At fictional Alder Telecom (international transit), this Junos network defect is reported: A provider edge redistributes selected connected customer prefixes into OSPF but an unrelated management subnet is also advertised. What should the specialist change first?

  1. Coordinate the OSPF authentication settings and validated keys on both ends, then inspect neighbor formation.
  2. Validate the stub area design and its ABR-supplied default route rather than forcing external LSAs into the stub.
  3. Narrow the OSPF export policy to approved routes and verify both accepted and rejected prefix samples.
  4. Check per-interface OSPF metrics and the calculated route cost, then set design-approved costs.

Explanation

Correct Answer

C:

Correct because the observable problem is: A provider edge redistributes selected connected customer prefixes into OSPF but an unrelated management subnet is also advertised. Use the controlled remedy: Narrow the OSPF export policy to approved routes and verify both accepted and rejected prefix samples. Confirm the resulting state with: Only the designated customer prefixes appear in OSPF advertisements and the management subnet remains absent.

Incorrect Answers

A:

That action would address the separate OSPF area authentication mismatch case, where An OSPF adjacency stops forming just after an authentication key rotation on only one routing device. The present OSPF route policy export issue instead requires: Narrow the OSPF export policy to approved routes and verify both accepted and rejected prefix samples.

B:

The proposal is a correction for OSPF stub area external reachability, not this situation: A provider edge redistributes selected connected customer prefixes into OSPF but an unrelated management subnet is also advertised. Here the cause is: The OSPF export policy matches a broader route set than the agreed service prefixes.

D:

That action would address the separate OSPF cost path preference case, where Two valid OSPF paths exist to a shared service subnet but the router consistently selects an expensive backup link. The present OSPF route policy export issue instead requires: Narrow the OSPF export policy to approved routes and verify both accepted and rejected prefix samples.

Question 107

A Junos routing specialist investigates at fictional Alder Telecom: A provider edge redistributes selected connected customer prefixes into OSPF but an unrelated management subnet is also advertised. What control gap requires attention?

  1. The link's MTU inconsistency prevents the intended database description exchange from completing.
  2. The expected link-state advertisement has not been originated or synchronized as intended for the target area.
  3. The OSPF export policy matches a broader route set than the agreed service prefixes.
  4. The cumulative OSPF cost values make the backup path more attractive than the planned primary path.

Explanation

Correct Answer

C:

The scenario is explained by: The OSPF export policy matches a broader route set than the agreed service prefixes. This is distinct from unrelated application failures. The recommended correction is: Narrow the OSPF export policy to approved routes and verify both accepted and rejected prefix samples.

Incorrect Answers

A:

The alternate cause would explain OSPF MTU exchange problem. For OSPF route policy export at Alder Telecom, the evidence instead supports: The OSPF export policy matches a broader route set than the agreed service prefixes.

B:

This is a different failure mechanism: The expected link-state advertisement has not been originated or synchronized as intended for the target area. The current symptom is: A provider edge redistributes selected connected customer prefixes into OSPF but an unrelated management subnet is also advertised. The more direct defect is: The OSPF export policy matches a broader route set than the agreed service prefixes.

D:

The alternate cause would explain OSPF cost path preference. For OSPF route policy export at Alder Telecom, the evidence instead supports: The OSPF export policy matches a broader route set than the agreed service prefixes.

Question 108

Following remediation at fictional Alder Telecom, how should the team verify that this specific issue is resolved? A provider edge redistributes selected connected customer prefixes into OSPF but an unrelated management subnet is also advertised.

  1. The peers exchange compatible Hellos and their OSPF neighbor adjacency converges to the expected state.
  2. The transit router forms its expected OSPF adjacency and the loopback continues to be advertised without an unnecessary neighbor.
  3. Access routers route permitted external destinations via the expected ABR default without individual AS-external LSAs.
  4. Only the designated customer prefixes appear in OSPF advertisements and the management subnet remains absent.

Explanation

Correct Answer

D:

Sign-off requires case-specific evidence: Only the designated customer prefixes appear in OSPF advertisements and the management subnet remains absent. Without that observation, the ospf export policy matches a broader route set than the agreed service prefixes.

Incorrect Answers

A:

The alternative proof tests a different cause: The OSPF hello and dead interval settings do not match across the intended neighboring interfaces. The relevant acceptance condition remains: Only the designated customer prefixes appear in OSPF advertisements and the management subnet remains absent.

B:

That result would validate the separate OSPF passive-loopback interface scenario (A transit interface accidentally inherits passive behavior, leaving its intended adjacent router absent although local OSPF routes are present.). It does not prove the needed OSPF route policy export outcome: Only the designated customer prefixes appear in OSPF advertisements and the management subnet remains absent.

C:

This observation is appropriate for OSPF stub area external reachability, not the OSPF route policy export defect at Alder Telecom. Verify instead: Only the designated customer prefixes appear in OSPF advertisements and the management subnet remains absent.

Question 109

After corrective implementation at fictional Alder Telecom, reviewers revisit: A provider edge redistributes selected connected customer prefixes into OSPF but an unrelated management subnet is also advertised. Which safeguard best protects the repaired state?

  1. Retest this approved Junos service-provider routing and switching control after relevant changes: OSPF neighbor inspection identifies distinct router IDs and stable route computation after the refresh.
  2. Retest this approved Junos service-provider routing and switching control after relevant changes: Operational logs demonstrate whether neighbor state, LSDB advertisement, or route installation is the failure stage.
  3. Retest this approved Junos service-provider routing and switching control after relevant changes: show ospf neighbor reports the correct peer in the expected adjacency state on the shared interface.
  4. Retest this approved Junos service-provider routing and switching control after relevant changes: Only the designated customer prefixes appear in OSPF advertisements and the management subnet remains absent.

Explanation

Correct Answer

D:

The repeated release test must confirm: Only the designated customer prefixes appear in OSPF advertisements and the management subnet remains absent. That check detects recurrence of the original defect: The OSPF export policy matches a broader route set than the agreed service prefixes.

Incorrect Answers

A:

This recurring check measures OSPF router ID duplication, whereas the fixed OSPF route policy export behavior needs ongoing evidence that: Only the designated customer prefixes appear in OSPF advertisements and the management subnet remains absent.

B:

That control would prevent the different failure The troubleshooting sequence skips adjacency and interface checks needed to separate protocol failure from route propagation failure. It would not detect recurrence of: The OSPF export policy matches a broader route set than the agreed service prefixes.

C:

The proposed check belongs to the separate OSPF area mismatch issue at Summit Transit. For this case, retest: Only the designated customer prefixes appear in OSPF advertisements and the management subnet remains absent.

Question 110

For fictional Alder Telecom, identify the shortcut that fails to address: A provider edge redistributes selected connected customer prefixes into OSPF but an unrelated management subnet is also advertised.

  1. Disable all routing policy and export every direct route to satisfy reachability.
  2. Increase OSPF interface priority while leaving area membership inconsistent.
  3. Change only the interface address while retaining duplicated OSPF router IDs.
  4. Convert every access area to a backbone area solely to expose external link-state entries.

Explanation

Correct Answer

A:

Reject this option for the observed incident at Alder Telecom: A provider edge redistributes selected connected customer prefixes into OSPF but an unrelated management subnet is also advertised. Use instead: Narrow the OSPF export policy to approved routes and verify both accepted and rejected prefix samples.

Incorrect Answers

B:

This alternative is problematic for OSPF area mismatch, rather than the reported OSPF route policy export. Corrective action here is: Narrow the OSPF export policy to approved routes and verify both accepted and rejected prefix samples.

C:

This shortcut would also be unsafe, but for a different OSPF router ID duplication case (Two routers on the same provider access segment receive overlapping OSPF identity alarms after cloning a configuration template.). It does not repeat the defect in this question: The OSPF export policy matches a broader route set than the agreed service prefixes.

D:

The proposal recreates the separate OSPF stub area external reachability error. The current case instead concerns: A provider edge redistributes selected connected customer prefixes into OSPF but an unrelated management subnet is also advertised. Its specific failed assumption is: The OSPF export policy matches a broader route set than the agreed service prefixes.

Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-364) Practice Tests

accept downloads in the last 7 days
What exactly is JN0-364 Premium File?

The JN0-364 Premium File has been developed by industry professionals, who have been working with IT certifications for years and have close ties with IT certification vendors and holders - with most recent exam questions and valid answers.

JN0-364 Premium File is presented in VCE format. VCE (Virtual CertExam) is a file format that realistically simulates JN0-364 exam environment, allowing for the most convenient exam preparation you can get - in the convenience of your own home or on the go. If you have ever seen IT exam simulations, chances are, they were in the VCE format.

What is VCE?

VCE is a file format associated with Visual CertExam Software. This format and software are widely used for creating tests for IT certifications. To create and open VCE files, you will need to purchase, download and install VCE Exam Simulator on your computer.

Can I try it for free?

Yes, you can. Look through free VCE files section and download any file you choose absolutely free.

Where do I get VCE Exam Simulator?

VCE Exam Simulator can be purchased from its developer, https://www.avanset.com. Please note that Exam-Labs does not sell or support this software. Should you have any questions or concerns about using this product, please contact Avanset support team directly.

How are Premium VCE files different from Free VCE files?

Premium VCE files have been developed by industry professionals, who have been working with IT certifications for years and have close ties with IT certification vendors and holders - with most recent exam questions and some insider information.

Free VCE files All files are sent by Exam-labs community members. We encourage everyone who has recently taken an exam and/or has come across some braindumps that have turned out to be true to share this information with the community by creating and sending VCE files. We don't say that these free VCEs sent by our members aren't reliable (experience shows that they are). But you should use your critical thinking as to what you download and memorize.

How long will I receive updates for JN0-364 Premium VCE File that I purchased?

Free updates are available during 30 days after you purchased Premium VCE file. After 30 days the file will become unavailable.

How can I get the products after purchase?

All products are available for download immediately from your Member's Area. Once you have made the payment, you will be transferred to Member's Area where you can login and download the products you have purchased to your PC or another device.

Will I be able to renew my products when they expire?

Yes, when the 30 days of your product validity are over, you have the option of renewing your expired products with a 30% discount. This can be done in your Member's Area.

Please note that you will not be able to use the product after it has expired if you don't renew it.

How often are the questions updated?

We always try to provide the latest pool of questions, Updates in the questions depend on the changes in actual pool of questions by different vendors. As soon as we know about the change in the exam question pool we try our best to update the products as fast as possible.

What is a Study Guide?

Study Guides available on Exam-Labs are built by industry professionals who have been working with IT certifications for years. Study Guides offer full coverage on exam objectives in a systematic approach. Study Guides are very useful for fresh applicants and provides background knowledge about preparation of exams.

How can I open a Study Guide?

Any study guide can be opened by an official Acrobat by Adobe or any other reader application you use.

What is a Training Course?

Training Courses we offer on Exam-Labs in video format are created and managed by IT professionals. The foundation of each course are its lectures, which can include videos, slides and text. In addition, authors can add resources and various types of practice activities, as a way to enhance the learning experience of students.

Enter Your Email Address to Proceed

Please fill out your email address below in order to purchase Certification/Exam.

A confirmation link will be sent to this email address to verify your login.

Make sure to enter correct email address.

Enter Your Email Address to Proceed

Please fill out your email address below in order to purchase Demo.

A confirmation link will be sent to this email address to verify your login.

Make sure to enter correct email address.

How It Works

Download Exam
Step 1. Choose Exam
on Exam-Labs
Download IT Exams Questions & Answers
Download Avanset Simulator
Step 2. Open Exam with
Avanset Exam Simulator
Press here to download VCE Exam Simulator that simulates latest exam environment
Study
Step 3. Study
& Pass
IT Exams Anywhere, Anytime!

SPECIAL OFFER: GET 10% OFF. This is ONE TIME OFFER

You save
10%
Save
Exam-Labs Special Discount

Enter Your Email Address to Receive Your 10% Off Discount Code

A confirmation link will be sent to this email address to verify your login

* We value your privacy. We will not rent or sell your email address.

SPECIAL OFFER: GET 10% OFF

You save
10%
Save
Exam-Labs Special Discount

USE DISCOUNT CODE:

A confirmation link was sent to your email.

Please check your mailbox for a message from [email protected] and follow the directions.