Includes questions types found on actual exam such as drag and drop, simulation, type in, and fill in the blank.
Service Provider Routing and Switching, Specialist (JNCIS-SP) JN0-364 Practice Test 14
Question 130
For fictional Ridgeway Wireless, identify the shortcut that fails to address: One circuit participates only in Level 1 on the remote router and only in Level 2 on the local router, preventing an adjacency.
Suppress all packet-loss alarms while retaining inconsistent adjacency timing.
Repeatedly clear the IS-IS adjacency without determining why the computed route was not installed.
Increase DIS priority despite the fact that the two peers have no common circuit level.
Reset BGP sessions because the OSPF neighbor list is empty on an IS-IS-only link.
Explanation
Correct Answer
C:
The proposed shortcut undermines the expected result: show isis adjacency displays the agreed Level 1 or Level 2 adjacency as Up. The safer implementation step is: Configure a mutually supported level on the intended link and verify the corresponding adjacency output.
Incorrect Answers
A:
This shortcut would also be unsafe, but for a different IS-IS hello holdtime mismatch case (An IS-IS peer periodically times out after a high-latency transport path was inserted between two provider routers.). It does not repeat the defect in this question: The enabled IS-IS circuit levels have no common level for an adjacency to form.
B:
The proposal recreates the separate IS-IS SPF route installation error. The current case instead concerns: One circuit participates only in Level 1 on the remote router and only in Level 2 on the local router, preventing an adjacency. Its specific failed assumption is: The enabled IS-IS circuit levels have no common level for an adjacency to form.
D:
This shortcut would also be unsafe, but for a different IS-IS adjacency command selection case (A junior engineer searches only show ospf neighbor when an IS-IS underlay loses a peer during maintenance.). It does not repeat the defect in this question: The enabled IS-IS circuit levels have no common level for an adjacency to form.
Question 131
At fictional Coastal IX (internet exchange), this Junos network defect is reported: An IS-IS peer periodically times out after a high-latency transport path was inserted between two provider routers. What should the specialist change first?
Inspect IS-IS database detail and ensure current LSP flooding and aging across the adjacency path.
Add and verify the loopback's appropriate IS-IS reachability without creating an unnecessary physical neighbor on loopback.
Align NET area membership for Level 1 adjacency according to the provider topology plan.
Inspect IS-IS Hello and hold-time settings plus loss and latency, then restore a stable supported transport or timer design.
Explanation
Correct Answer
D:
This response addresses the specific IS-IS hello holdtime mismatch failure at Coastal IX. Apply: Inspect IS-IS Hello and hold-time settings plus loss and latency, then restore a stable supported transport or timer design. Its acceptance test is: The adjacency remains Up across the tested transport condition and hold timers no longer expire prematurely.
Incorrect Answers
A:
The proposal is a correction for IS-IS LSP freshness, not this situation: An IS-IS peer periodically times out after a high-latency transport path was inserted between two provider routers. Here the cause is: The IS-IS neighbor hold-time behavior cannot tolerate the observed Hello delivery pattern on the transport.
B:
Although relevant to IS-IS passive loopback, this configuration does not remedy the reported IS-IS hello holdtime mismatch failure. Use: Inspect IS-IS Hello and hold-time settings plus loss and latency, then restore a stable supported transport or timer design.
C:
That action would address the separate IS-IS NET area mismatch case, where Two intended Level 1 IS-IS peers on the same fiber have healthy Ethernet connectivity but cannot establish a Level 1 adjacency. The present IS-IS hello holdtime mismatch issue instead requires: Inspect IS-IS Hello and hold-time settings plus loss and latency, then restore a stable supported transport or timer design.
Question 132
A Junos routing specialist investigates at fictional Coastal IX: An IS-IS peer periodically times out after a high-latency transport path was inserted between two provider routers. What control gap requires attention?
The enabled IS-IS circuit levels have no common level for an adjacency to form.
The router NET area addresses differ, so the peers cannot share the required Level 1 area.
The topology database must reconcile LSP sequence number, lifetime, flooding and current originator state.
The IS-IS neighbor hold-time behavior cannot tolerate the observed Hello delivery pattern on the transport.
Explanation
Correct Answer
D:
Fictional Coastal IX demonstrates this underlying defect: The IS-IS neighbor hold-time behavior cannot tolerate the observed Hello delivery pattern on the transport. Validate after remediation by checking: The adjacency remains Up across the tested transport condition and hold timers no longer expire prematurely.
Incorrect Answers
A:
This is a different failure mechanism: The enabled IS-IS circuit levels have no common level for an adjacency to form. The current symptom is: An IS-IS peer periodically times out after a high-latency transport path was inserted between two provider routers. The more direct defect is: The IS-IS neighbor hold-time behavior cannot tolerate the observed Hello delivery pattern on the transport.
B:
That diagnosis belongs to IS-IS NET area mismatch, for example: Two intended Level 1 IS-IS peers on the same fiber have healthy Ethernet connectivity but cannot establish a Level 1 adjacency. It does not explain this case, which is caused by: The IS-IS neighbor hold-time behavior cannot tolerate the observed Hello delivery pattern on the transport.
C:
The alternate cause would explain IS-IS LSP freshness. For IS-IS hello holdtime mismatch at Coastal IX, the evidence instead supports: The IS-IS neighbor hold-time behavior cannot tolerate the observed Hello delivery pattern on the transport.
Question 133
Following remediation at fictional Coastal IX, how should the team verify that this specific issue is resolved? An IS-IS peer periodically times out after a high-latency transport path was inserted between two provider routers.
show route advertising-protocol isis output excludes the lab prefix and includes sanctioned exports.
show isis adjacency reports an Up Level 1 peer and the intended area routes appear.
The troubleshooting record names the IS-IS interface, peer system ID, level, and Up or Down state.
The adjacency remains Up across the tested transport condition and hold timers no longer expire prematurely.
Explanation
Correct Answer
D:
The acceptance criterion must prove the original behavior changed: The adjacency remains Up across the tested transport condition and hold timers no longer expire prematurely. This follows from the remedial action: Inspect IS-IS Hello and hold-time settings plus loss and latency, then restore a stable supported transport or timer design.
Incorrect Answers
A:
That result would validate the separate IS-IS policy route export scenario (A boundary router leaks a laboratory prefix into the provider IS-IS domain despite an approved limited export scope.). It does not prove the needed IS-IS hello holdtime mismatch outcome: The adjacency remains Up across the tested transport condition and hold timers no longer expire prematurely.
B:
This observation is appropriate for IS-IS NET area mismatch, not the IS-IS hello holdtime mismatch defect at Coastal IX. Verify instead: The adjacency remains Up across the tested transport condition and hold timers no longer expire prematurely.
C:
The alternative proof tests a different cause: The operational inspection is directed at the wrong routing protocol and cannot reveal IS-IS adjacency state. The relevant acceptance condition remains: The adjacency remains Up across the tested transport condition and hold timers no longer expire prematurely.
Question 134
After corrective implementation at fictional Coastal IX, reviewers revisit: An IS-IS peer periodically times out after a high-latency transport path was inserted between two provider routers. Which safeguard best protects the repaired state?
Retest this approved Junos service-provider routing and switching control after relevant changes: The adjacency remains Up across the tested transport condition and hold timers no longer expire prematurely.
Retest this approved Junos service-provider routing and switching control after relevant changes: All relevant peers have current LSP sequence state and the removed link no longer drives SPF selection.
Retest this approved Junos service-provider routing and switching control after relevant changes: The expected IS-IS prefix is eligible and installed in the proper RIB and forwarding table.
Retest this approved Junos service-provider routing and switching control after relevant changes: show route advertising-protocol isis output excludes the lab prefix and includes sanctioned exports.
Explanation
Correct Answer
A:
A recurring safeguard for IS-IS hello holdtime mismatch should test this actual outcome: The adjacency remains Up across the tested transport condition and hold timers no longer expire prematurely. It exercises the configured correction: Inspect IS-IS Hello and hold-time settings plus loss and latency, then restore a stable supported transport or timer design.
Incorrect Answers
B:
The proposed check belongs to the separate IS-IS LSP freshness issue at Cedar Mobile. For this case, retest: The adjacency remains Up across the tested transport condition and hold timers no longer expire prematurely.
C:
This recurring check measures IS-IS SPF route installation, whereas the fixed IS-IS hello holdtime mismatch behavior needs ongoing evidence that: The adjacency remains Up across the tested transport condition and hold timers no longer expire prematurely.
D:
That control would prevent the different failure The IS-IS export policy does not sufficiently constrain redistributed reachable prefixes. It would not detect recurrence of: The IS-IS neighbor hold-time behavior cannot tolerate the observed Hello delivery pattern on the transport.
Question 135
For fictional Coastal IX, identify the shortcut that fails to address: An IS-IS peer periodically times out after a high-latency transport path was inserted between two provider routers.
Change only IS-IS interface metric values while leaving the Level 1 NET area mismatch.
Suppress all packet-loss alarms while retaining inconsistent adjacency timing.
Increase DIS priority despite the fact that the two peers have no common circuit level.
Reset BGP sessions because the OSPF neighbor list is empty on an IS-IS-only link.
Explanation
Correct Answer
B:
That shortcut preserves the original IS-IS hello holdtime mismatch weakness: The IS-IS neighbor hold-time behavior cannot tolerate the observed Hello delivery pattern on the transport. The controlled alternative is: Inspect IS-IS Hello and hold-time settings plus loss and latency, then restore a stable supported transport or timer design.
Incorrect Answers
A:
This alternative is problematic for IS-IS NET area mismatch, rather than the reported IS-IS hello holdtime mismatch. Corrective action here is: Inspect IS-IS Hello and hold-time settings plus loss and latency, then restore a stable supported transport or timer design.
C:
The proposal recreates the separate IS-IS circuit-level mismatch error. The current case instead concerns: An IS-IS peer periodically times out after a high-latency transport path was inserted between two provider routers. Its specific failed assumption is: The IS-IS neighbor hold-time behavior cannot tolerate the observed Hello delivery pattern on the transport.
D:
This alternative is problematic for IS-IS adjacency command selection, rather than the reported IS-IS hello holdtime mismatch. Corrective action here is: Inspect IS-IS Hello and hold-time settings plus loss and latency, then restore a stable supported transport or timer design.
Question 136
At fictional Trellis Education (campus WAN), this Junos network defect is reported: A technician sees only one designated intermediate system listed on a multiaccess IS-IS LAN and assumes a backup DIS must also be elected. What should the specialist change first?
Verify both interfaces support Level 2 and correct protocol reachability rather than needlessly merging area identifiers.
Inspect DIS priority and pseudonode ownership and validate normal IS-IS election behavior.
Apply an explicit policy permitting the intended routes and rejecting the laboratory prefix before advertisement.
Compare cumulative IS-IS metrics and set approved interface values for the intended primary and standby paths.
Explanation
Correct Answer
B:
This response addresses the specific IS-IS DIS election failure at Trellis Education. Apply: Inspect DIS priority and pseudonode ownership and validate normal IS-IS election behavior. Its acceptance test is: The expected active DIS originates the LAN pseudonode LSP and a new DIS is elected if it fails.
Incorrect Answers
A:
That action would address the separate IS-IS Level 2 interarea adjacency case, where Operators expect two Level 2 routers in different IS-IS areas to peer, but a teammate proposes giving them identical area IDs. The present IS-IS DIS election issue instead requires: Inspect DIS priority and pseudonode ownership and validate normal IS-IS election behavior.
C:
Although relevant to IS-IS policy route export, this configuration does not remedy the reported IS-IS DIS election failure. Use: Inspect DIS priority and pseudonode ownership and validate normal IS-IS election behavior.
D:
That action would address the separate IS-IS metric traffic engineering case, where Two IS-IS paths are both reachable but the network keeps using a high-latency satellite hop rather than the engineered terrestrial route. The present IS-IS DIS election issue instead requires: Inspect DIS priority and pseudonode ownership and validate normal IS-IS election behavior.
Question 137
A Junos routing specialist investigates at fictional Trellis Education: A technician sees only one designated intermediate system listed on a multiaccess IS-IS LAN and assumes a backup DIS must also be elected. What control gap requires attention?
The intended stable loopback reachability is not included in IS-IS advertisements or supporting routing policy.
IS-IS elects a DIS for a LAN pseudonode and does not use the OSPF DR and BDR election model.
The IS-IS neighbor hold-time behavior cannot tolerate the observed Hello delivery pattern on the transport.
The enabled IS-IS circuit levels have no common level for an adjacency to form.
Explanation
Correct Answer
B:
Fictional Trellis Education demonstrates this underlying defect: IS-IS elects a DIS for a LAN pseudonode and does not use the OSPF DR and BDR election model. Validate after remediation by checking: The expected active DIS originates the LAN pseudonode LSP and a new DIS is elected if it fails.
Incorrect Answers
A:
The alternate cause would explain IS-IS passive loopback. For IS-IS DIS election at Trellis Education, the evidence instead supports: IS-IS elects a DIS for a LAN pseudonode and does not use the OSPF DR and BDR election model.
C:
That diagnosis belongs to IS-IS hello holdtime mismatch, for example: An IS-IS peer periodically times out after a high-latency transport path was inserted between two provider routers. It does not explain this case, which is caused by: IS-IS elects a DIS for a LAN pseudonode and does not use the OSPF DR and BDR election model.
D:
The alternate cause would explain IS-IS circuit-level mismatch. For IS-IS DIS election at Trellis Education, the evidence instead supports: IS-IS elects a DIS for a LAN pseudonode and does not use the OSPF DR and BDR election model.
Question 138
Following remediation at fictional Trellis Education, how should the team verify that this specific issue is resolved? A technician sees only one designated intermediate system listed on a multiaccess IS-IS LAN and assumes a backup DIS must also be elected.
The loopback prefix is present in the intended IS-IS tables and remains reachable after transit link changes.
The adjacency remains Up across the tested transport condition and hold timers no longer expire prematurely.
The expected active DIS originates the LAN pseudonode LSP and a new DIS is elected if it fails.
Route selection prefers the terrestrial path under normal conditions and falls back on failure.
Explanation
Correct Answer
C:
This outcome directly measures IS-IS DIS election: The expected active DIS originates the LAN pseudonode LSP and a new DIS is elected if it fails. It tests the diagnosed issue: IS-IS elects a DIS for a LAN pseudonode and does not use the OSPF DR and BDR election model.
Incorrect Answers
A:
The alternative proof tests a different cause: The intended stable loopback reachability is not included in IS-IS advertisements or supporting routing policy. The relevant acceptance condition remains: The expected active DIS originates the LAN pseudonode LSP and a new DIS is elected if it fails.
B:
That result would validate the separate IS-IS hello holdtime mismatch scenario (An IS-IS peer periodically times out after a high-latency transport path was inserted between two provider routers.). It does not prove the needed IS-IS DIS election outcome: The expected active DIS originates the LAN pseudonode LSP and a new DIS is elected if it fails.
D:
The alternative proof tests a different cause: Configured IS-IS link metrics do not reflect the intended provider path cost policy. The relevant acceptance condition remains: The expected active DIS originates the LAN pseudonode LSP and a new DIS is elected if it fails.
Question 139
After corrective implementation at fictional Trellis Education, reviewers revisit: A technician sees only one designated intermediate system listed on a multiaccess IS-IS LAN and assumes a backup DIS must also be elected. Which safeguard best protects the repaired state?
Retest this approved Junos service-provider routing and switching control after relevant changes: The expected active DIS originates the LAN pseudonode LSP and a new DIS is elected if it fails.
Retest this approved Junos service-provider routing and switching control after relevant changes: Route selection prefers the terrestrial path under normal conditions and falls back on failure.
Retest this approved Junos service-provider routing and switching control after relevant changes: The troubleshooting record names the IS-IS interface, peer system ID, level, and Up or Down state.
Retest this approved Junos service-provider routing and switching control after relevant changes: The decoded LSP distinguishes each supported TLV and correctly presents intended prefixes or attributes.
Explanation
Correct Answer
A:
The repeated release test must confirm: The expected active DIS originates the LAN pseudonode LSP and a new DIS is elected if it fails. That check detects recurrence of the original defect: IS-IS elects a DIS for a LAN pseudonode and does not use the OSPF DR and BDR election model.
Incorrect Answers
B:
That control would prevent the different failure Configured IS-IS link metrics do not reflect the intended provider path cost policy. It would not detect recurrence of: IS-IS elects a DIS for a LAN pseudonode and does not use the OSPF DR and BDR election model.
C:
The proposed check belongs to the separate IS-IS adjacency command selection issue at Sterling Cloud. For this case, retest: The expected active DIS originates the LAN pseudonode LSP and a new DIS is elected if it fails.
D:
This recurring check measures IS-IS TLV interpretation, whereas the fixed IS-IS DIS election behavior needs ongoing evidence that: The expected active DIS originates the LAN pseudonode LSP and a new DIS is elected if it fails.
Question 140
For fictional Trellis Education, identify the shortcut that fails to address: A technician sees only one designated intermediate system listed on a multiaccess IS-IS LAN and assumes a backup DIS must also be elected.
Manually configure a permanent static summary to conceal the stale LSP while topology remains wrong.
Suppress all packet-loss alarms while retaining inconsistent adjacency timing.
Change only IS-IS interface metric values while leaving the Level 1 NET area mismatch.
Configure an OSPF-style BDR requirement as though it were part of IS-IS.
Explanation
Correct Answer
D:
Reject this option for the observed incident at Trellis Education: A technician sees only one designated intermediate system listed on a multiaccess IS-IS LAN and assumes a backup DIS must also be elected. Use instead: Inspect DIS priority and pseudonode ownership and validate normal IS-IS election behavior.
Incorrect Answers
A:
The proposal recreates the separate IS-IS LSP freshness error. The current case instead concerns: A technician sees only one designated intermediate system listed on a multiaccess IS-IS LAN and assumes a backup DIS must also be elected. Its specific failed assumption is: IS-IS elects a DIS for a LAN pseudonode and does not use the OSPF DR and BDR election model.
B:
This alternative is problematic for IS-IS hello holdtime mismatch, rather than the reported IS-IS DIS election. Corrective action here is: Inspect DIS priority and pseudonode ownership and validate normal IS-IS election behavior.
C:
This shortcut would also be unsafe, but for a different IS-IS NET area mismatch case (Two intended Level 1 IS-IS peers on the same fiber have healthy Ethernet connectivity but cannot establish a Level 1 adjacency.). It does not repeat the defect in this question: IS-IS elects a DIS for a LAN pseudonode and does not use the OSPF DR and BDR election model.
Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-364) Practice Tests
Our team works hard to provide students with high exam practice test questions and compelling learning experiences. We're confident of the quality level of the products we offer and provide no hassle satisfaction guarantee.
Why choose Exam-Labs?613,682+Satisfied Customers since 2015
100% Latest Exam Questions
Accurate & Updated Answers
Regular Free Updates
24/7 Customer Support
Instant Download
Exam Info
Juniper JN0-364 Practice Test Questions, Juniper JN0-364 Exam Practice Test Questions
Looking to pass your tests the first time. You can study with Juniper JN0-364 certification practice test questions and answers, study guide, training courses. With Exam-Labs VCE files you can prepare with Juniper JN0-364 Service Provider Routing and Switching, Specialist (JNCIS-SP) exam practice test questions and answers. The most complete solution for passing with Juniper certification JN0-364 exam practice test questions and answers, study guide, training course.
JN0-364 Service Provider Routing and Switching, Specialist
JN0-364 is the current Service Provider Routing and Switching, Specialist exam as of October 2026. HPE Juniper Networking lists 65 multiple-choice questions in 90 minutes, Pearson VUE delivery, JNCIA-Junos as the prerequisite, and Junos OS 25.2 as the software reference. It replaced JN0-363 on February 2, 2026.
The blueprint is broad: protocol-independent routing, OSPF, IS-IS, BGP, Layer 2 bridging and VLANs, spanning-tree variants, MPLS, IPv6, GRE tunnels, and high availability. The common thread is service-provider operations. Candidates must understand not only what each protocol does but how state is configured, verified, and troubleshot across a Junos network.
The current JN0-106 associate exam provides the Junos foundation. If routing tables, policy, interface hierarchy, or operational mode are still slow, strengthen those first. JN0-364 adds enough simultaneous control planes that weak fundamentals become a major study bottleneck.
Protocol-independent routing is the control surface beneath the protocols
The blueprint includes static, aggregate, and generated routes, martian addresses, routing instances, RIB groups, load balancing, and filter-based forwarding. These are not secondary topics. They determine which tables routes enter, which paths become active, and how traffic can be steered independently of the dynamic protocol that learned a prefix.
Build labs where the same destination appears from multiple sources. Change route preference, create an aggregate, move information between routing instances, and apply filter-based forwarding. Before running a show command, predict which route should be active and why. That habit turns the routing table into a reasoned outcome rather than a display to memorize.
The concepts behind static routing make a clean baseline because they isolate local route selection before dynamic signaling complicates the picture.
OSPF and IS-IS should be practiced as living topology databases
For OSPF, JN0-364 expects knowledge of the link-state database, packet types, router IDs, neighbors, DR/BDR roles, area and router types, LSAs, configuration, policy, and troubleshooting. For IS-IS, candidates need PDUs, TLVs, levels, areas, adjacencies, DIS behavior, metrics, policy, and operational verification.
Do not study those items as vocabulary lists. Form a neighbor, inspect the database, change a metric, remove a link, and watch the shortest-path result change. Repeat the topology with the other protocol. This makes the shared link-state model visible while preserving the differences in hierarchy and protocol behavior.
The detailed explanation of OSPF areas and LSAs is useful, but a service-provider candidate should be equally comfortable reading IS-IS adjacency and database state.
BGP should be verified at every stage between peer and forwarding table
JN0-364 covers BGP messages, attributes, route selection, IBGP/EBGP interaction, peers, options, policy, and troubleshooting. A disciplined verification sequence is essential: confirm transport and session state, inspect received routes, apply policy reasoning, verify next-hop resolution, inspect active routes, and check what is advertised onward.
Create at least one lab where the BGP session remains Established while the desired route disappears. Use import policy, an unreachable next hop, or a competing path. The exercise proves why “peer up” and “service working” are different statements. The broader mechanics of BGP path selection become easier to apply when every attribute change produces visible route-state evidence.
Service-provider BGP work is inseparable from policy. Spend time writing and reading policy terms so that you can explain exactly why a route is accepted, rejected, modified, or exported.
Provider switching topics protect the service edge
The Layer 2 domain includes service-provider switching platforms, bridging concepts, frame processing, virtual switches, Q-in-Q provider bridging, VLAN port modes, tagging, IRB, and spanning-tree variants. These topics matter because service-provider networks often carry customer Layer 2 services even when the core itself is highly routed.
Practice Q-in-Q by distinguishing customer tags from the service-provider tag. Then verify how the frame is handled at ingress, across the provider domain, and at egress. This makes the separation between customer segmentation and provider forwarding explicit.
Spanning tree should be understood with security controls such as BPDU, loop, and root protection. Those features encode expectations at the edge and help prevent customer or access faults from destabilizing a larger Layer 2 domain.
MPLS study should begin with packet forwarding before signaling
The current blueprint includes MPLS terminology, label headers, end-to-end forwarding, label information, routing-table relationships, RSVP, LDP, and segment routing with MPLS. Start with the dataplane. Trace how an ingress node pushes a label, how transit nodes swap it, and how the egress processes the final label.
Then attach each signaling method to the label-switched path it creates. LDP distributes labels along routing paths, RSVP can establish traffic-engineered paths, and segment routing expresses path intent through segments. The concepts in MPLS forwarding provide a strong base when paired with Junos route and label-table output.
Do not memorize labels as static numbers. Focus on the control information that creates them and the forwarding behavior they enable. That perspective scales into VPN and traffic-engineering work at the professional level.
When comparing MPLS control methods, keep one question in view: what information tells the router which labeled path to use? LDP generally couples label distribution to IGP reachability, RSVP can signal traffic-engineered LSPs with explicit constraints, and segment routing represents path intent through ordered segments. Practice reading the resulting state rather than memorizing a feature table. If an LSP is down, determine whether the missing evidence is an IGP route, a signaling relationship, a label binding, or the forwarding entry itself.
Troubleshooting should therefore move from dependency to dependent feature. Verify core addressing and IGP reachability first, then protocol sessions, then label or tunnel state, and finally end-to-end service traffic. This sequence is efficient because later layers cannot be healthy when their transport assumptions are false. It also mirrors real service-provider operations, where the fastest resolution often comes from proving the lowest broken dependency before touching policy or service configuration.
IPv6 belongs in the same routing model as IPv4
JN0-364 covers IPv6 static routing and dynamic routing through OSPFv3, IS-IS, and BGP, plus IPv6-over-IPv4 tunneling. Treat IPv6 as a routed protocol with its own addressing and neighbor behavior rather than as a separate specialty. Route selection, policy, protocol adjacency, and troubleshooting discipline still apply.
Build dual-stack labs so you can compare the same topology under both address families. Verify that a protocol session can be healthy for one family while reachability for another is absent. This teaches you to inspect family-specific route state instead of assuming that one working path proves the other.
For transition tunnels, explicitly trace the outer IPv4 path and the inner IPv6 packet. The layered model is the same one used for GRE and prevents confusion about which address family is failing.
GRE tunnels add reachability without removing underlay dependencies
The tunnel objective covers applications, design considerations, GRE configuration, and troubleshooting. A GRE interface can make two remote networks appear directly connected at the logical layer, but the outer endpoints still depend on ordinary routing. If the underlay cannot reach the tunnel destination, the overlay path cannot work.
In the lab, verify outer routes, tunnel source and destination, inner routing, and MTU. Then break each independently. The difference between an underlay failure and an inner-route problem becomes obvious when you compare packet captures and interface state.
Use the conceptual discussion of GRE tunneling to broaden understanding, while keeping configuration practice aligned to the exact JN0-364 objectives.
High availability combines fast detection with preserved forwarding
Current HA topics include LAG, graceful restart, GRES, NSB, NSR, BFD, and VRRP. Each protects a different part of service continuity. Link aggregation addresses physical path loss, BFD accelerates failure detection, graceful and nonstop mechanisms reduce control-plane disruption, and VRRP protects the first-hop gateway identity.
Build a table that states for each feature what fails, what detects the failure, what state is preserved, and what alternate path or node takes over. The principles of VRRP redundancy are especially useful when contrasted with BFD: one provides a virtual gateway role, the other supplies rapid liveness information.
In testing, record packets lost and convergence time. A protocol can be “working as designed” while still failing a service-level objective if recovery is too slow for the application.
Study the current exam as one service-provider system
Separate notebooks for OSPF, BGP, MPLS, and HA are useful early, but final preparation should combine them. Build a topology where an IGP supplies core reachability, MPLS uses that underlay, BGP carries service or external routes, and HA mechanisms protect critical paths. Then introduce a fault and decide which control plane should react.
Use the objective list as a four-part readiness matrix: explain, configure, verify, troubleshoot. If you can define a feature but cannot identify healthy operational output, the topic is incomplete. If you can configure it but cannot predict the effect of a failure, it is not yet specialist-level knowledge.
The current professional progression represented in the approved inventory is JN0-664. That path rewards candidates who build durable service-provider reasoning now, because advanced Layer 2 VPN, EVPN, MPLS, and policy work assumes the specialist foundation is already fluent.
Before scheduling, verify the live JN0-364 blueprint and software reference again. The certification program's branding changed under HPE Networking in September 2026, but the exam remains centered on Junos service-provider routing and switching. Use current first-party objectives for scope and let hands-on operational evidence—routes, adjacencies, labels, policy results, tunnel state, and failover behavior—drive the final review.
Use Juniper JN0-364 certification exam practice test questions, study guide and training course - the complete package at discounted price. Pass with JN0-364 Service Provider Routing and Switching, Specialist (JNCIS-SP) practice test questions and answers, study guide, complete training course especially formatted in VCE files. Latest Juniper certification JN0-364 exam practice test questions and answers will guarantee your success without studying for endless hours.
FAQs
Juniper JN0-364 Exam Practice Test Questions, Juniper JN0-364 Practice Test Questions and Answers
Do you have questions about our JN0-364 Service Provider Routing and Switching, Specialist (JNCIS-SP) practice test questions and answers or any of our products? If you are not clear about our Juniper JN0-364 exam practice test questions, you can read the FAQ below.
The JN0-364 Premium File has been developed by industry professionals, who have been working with IT certifications for years and have close ties with IT certification vendors and holders - with most recent exam questions and valid answers.
JN0-364 Premium File is presented in VCE format. VCE (Virtual CertExam) is a file format that realistically simulates JN0-364 exam environment, allowing for the most convenient exam preparation you can get - in the convenience of your own home or on the go. If you have ever seen IT exam simulations, chances are, they were in the VCE format.
What is VCE?
VCE is a file format associated with Visual CertExam Software. This format and software are widely used for creating tests for IT certifications. To create and open VCE files, you will need to purchase, download and install VCE Exam Simulator on your computer.
Can I try it for free?
Yes, you can. Look through free VCE files section and download any file you choose absolutely free.
Where do I get VCE Exam Simulator?
VCE Exam Simulator can be purchased from its developer, https://www.avanset.com. Please note that Exam-Labs does not sell or support this software. Should you have any questions or concerns about using this product, please contact Avanset support team directly.
How are Premium VCE files different from Free VCE files?
Premium VCE files have been developed by industry professionals, who have been working with IT certifications for years and have close ties with IT certification vendors and holders - with most recent exam questions and some insider information.
Free VCE files All files are sent by Exam-labs community members. We encourage everyone who has recently taken an exam and/or has come across some braindumps that have turned out to be true to share this information with the community by creating and sending VCE files. We don't say that these free VCEs sent by our members aren't reliable (experience shows that they are). But you should use your critical thinking as to what you download and memorize.
How long will I receive updates for JN0-364 Premium VCE File that I purchased?
Free updates are available during 30 days after you purchased Premium VCE file. After 30 days the file will become unavailable.
How can I get the products after purchase?
All products are available for download immediately from your Member's Area. Once you have made the payment, you will be transferred to Member's Area where you can login and download the products you have purchased to your PC or another device.
Will I be able to renew my products when they expire?
Yes, when the 30 days of your product validity are over, you have the option of renewing your expired products with a 30% discount. This can be done in your Member's Area.
Please note that you will not be able to use the product after it has expired if you don't renew it.
How often are the questions updated?
We always try to provide the latest pool of questions, Updates in the questions depend on the changes in actual pool of questions by different vendors. As soon as we know about the change in the exam question pool we try our best to update the products as fast as possible.
What is a Study Guide?
Study Guides available on Exam-Labs are built by industry professionals who have been working with IT certifications for years. Study Guides offer full coverage on exam objectives in a systematic approach. Study Guides are very useful for fresh applicants and provides background knowledge about preparation of exams.
How can I open a Study Guide?
Any study guide can be opened by an official Acrobat by Adobe or any other reader application you use.
What is a Training Course?
Training Courses we offer on Exam-Labs in video format are created and managed by IT professionals. The foundation of each course are its lectures, which can include videos, slides and text. In addition, authors can add resources and various types of practice activities, as a way to enhance the learning experience of students.
Enter Your Email Address to Proceed
Please fill out your email address below in order to purchase Certification/Exam.
Enter Your Email Address to Proceed
Please fill out your email address below in order to purchase Demo.
How It Works
Step 1. Choose Exam on Exam-Labs
Download IT Exams Questions & Answers
Step 2. Open Exam with Avanset Exam Simulator
Press here to download VCE Exam Simulator that simulates latest exam environment