Includes questions types found on actual exam such as drag and drop, simulation, type in, and fill in the blank.
Enterprise Routing and Switching, Professional (JNCIP-ENT) JN0-650 Practice Test 40
Question 390
A change board is reviewing whether the following fault is corrected: Multicast frames duplicate to a dual-homed Ethernet segment because both attached leafs forward BUM traffic to the segment. Which observation is decisive?
The EVPN BGP table contains expected Type 2 and Type 3 routes without changing the underlay protocol.
Only the elected DF forwards BUM traffic toward the shared segment while the other peer remains standby for that function.
The failing member's Ethernet A-D route is withdrawn and remote forwarding uses surviving eligible PEs.
Duplicate-MAC alarms clear after removing the unintended attachment and one authorized MAC location remains.
Explanation
Correct Answer
B:
EVPN designated forwarder selection prevents duplicate BUM delivery on all-active multihomed segments. The observed evidence is decisive here because only the elected DF forwards BUM traffic toward the shared segment while the other peer remains standby for that function. This tests the actual EVPN designated forwarder condition rather than an unrelated operational symptom.
Incorrect Answers
A:
“The EVPN BGP table contains expected Type 2 and Type 3 routes without changing the underlay protocol” is relevant when eVPN uses its own BGP address family for overlay reachability separate from IPv4 unicast NLRI. The observed evidence is decisive here because the EVPN BGP table contains expected Type 2 and Type 3 routes without changing the underlay protocol. The Juniper control here is “Only the elected DF forwards BUM traffic toward the shared segment while the other peer remains standby for that function”, supported by this specific technical distinction: EVPN designated forwarder selection prevents duplicate BUM delivery on all-active multihomed segments. The observed evidence is decisive here because only the elected DF forwards BUM traffic toward the shared segment while the other peer remains standby for that function.
C:
“The failing member's Ethernet A-D route is withdrawn and remote forwarding uses surviving eligible PEs” is relevant when eVPN Type 1 routes signal Ethernet-segment reachability and support multihoming convergence. The observed evidence is decisive here because the failing member's Ethernet A-D route is withdrawn and remote forwarding uses surviving eligible PEs. The Juniper control here is “Only the elected DF forwards BUM traffic toward the shared segment while the other peer remains standby for that function”, supported by this specific technical distinction: EVPN designated forwarder selection prevents duplicate BUM delivery on all-active multihomed segments. The observed evidence is decisive here because only the elected DF forwards BUM traffic toward the shared segment while the other peer remains standby for that function.
D:
“Duplicate-MAC alarms clear after removing the unintended attachment and one authorized MAC location remains” is relevant when a MAC learned at contradictory non-multihomed locations can signal a loop or duplicate identity. The observed evidence is decisive here because duplicate-MAC alarms clear after removing the unintended attachment and one authorized MAC location remains. The Juniper control here is “Only the elected DF forwards BUM traffic toward the shared segment while the other peer remains standby for that function”, supported by this specific technical distinction: EVPN designated forwarder selection prevents duplicate BUM delivery on all-active multihomed segments. The observed evidence is decisive here because only the elected DF forwards BUM traffic toward the shared segment while the other peer remains standby for that function.
Question 391
During a Juniper network cutover, the team finds: A virtual machine moves between leafs, but traffic still follows the original leaf's stale MAC location. What is the best targeted engineering action?
Investigate duplicate-MAC detection and verify whether any move is legitimate before allowing competing advertisements.
Enable supported BGP EVPN signaling family between the intended route peers with necessary import/export policy.
Trace EVPN MAC mobility sequence signaling and withdraw or supersede obsolete Type 2 MAC routes.
Check ESI multihoming state, Type 1 withdrawal, surviving Type 2 routes and underlay next-hop convergence.
Explanation
Correct Answer
C:
EVPN MAC mobility conveys a change of host location so remote VTEPs update forwarding. The specifically applicable intervention is: Trace EVPN MAC mobility sequence signaling and withdraw or supersede obsolete Type 2 MAC routes. A discriminating confirmation would be: Remote MAC tables point to the new VTEP and traffic follows the migrated host without persistent blackholes.
Incorrect Answers
A:
“Investigate duplicate-MAC detection and verify whether any move is legitimate before allowing competing advertisements” is relevant when a MAC learned at contradictory non-multihomed locations can signal a loop or duplicate identity. The Juniper control here is “Trace EVPN MAC mobility sequence signaling and withdraw or supersede obsolete Type 2 MAC routes”, supported by this specific technical distinction: EVPN MAC mobility conveys a change of host location so remote VTEPs update forwarding.
B:
“Enable supported BGP EVPN signaling family between the intended route peers with necessary import/export policy” is relevant when eVPN uses its own BGP address family for overlay reachability separate from IPv4 unicast NLRI. The Juniper control here is “Trace EVPN MAC mobility sequence signaling and withdraw or supersede obsolete Type 2 MAC routes”, supported by this specific technical distinction: EVPN MAC mobility conveys a change of host location so remote VTEPs update forwarding.
D:
“Check ESI multihoming state, Type 1 withdrawal, surviving Type 2 routes and underlay next-hop convergence” is relevant when eVPN multihoming resiliency depends on correct Ethernet-segment signaling and reachable surviving VTEPs. The Juniper control here is “Trace EVPN MAC mobility sequence signaling and withdraw or supersede obsolete Type 2 MAC routes”, supported by this specific technical distinction: EVPN MAC mobility conveys a change of host location so remote VTEPs update forwarding.
Question 392
An engineer is closing a ticket for: A virtual machine moves between leafs, but traffic still follows the original leaf's stale MAC location. Which observed state supports closing the fault?
Duplicate-MAC alarms clear after removing the unintended attachment and one authorized MAC location remains.
Remote MAC tables point to the new VTEP and traffic follows the migrated host without persistent blackholes.
The EVPN BGP table contains expected Type 2 and Type 3 routes without changing the underlay protocol.
A controlled leaf failure preserves tenant reachability through the remaining advertised EVPN path.
Explanation
Correct Answer
B:
EVPN MAC mobility conveys a change of host location so remote VTEPs update forwarding. The observed evidence is decisive here because remote MAC tables point to the new VTEP and traffic follows the migrated host without persistent blackholes. This tests the actual EVPN MAC mobility condition rather than an unrelated operational symptom.
Incorrect Answers
A:
“Duplicate-MAC alarms clear after removing the unintended attachment and one authorized MAC location remains” is relevant when a MAC learned at contradictory non-multihomed locations can signal a loop or duplicate identity. The observed evidence is decisive here because duplicate-MAC alarms clear after removing the unintended attachment and one authorized MAC location remains. The Juniper control here is “Remote MAC tables point to the new VTEP and traffic follows the migrated host without persistent blackholes”, supported by this specific technical distinction: EVPN MAC mobility conveys a change of host location so remote VTEPs update forwarding. The observed evidence is decisive here because remote MAC tables point to the new VTEP and traffic follows the migrated host without persistent blackholes.
C:
“The EVPN BGP table contains expected Type 2 and Type 3 routes without changing the underlay protocol” is relevant when eVPN uses its own BGP address family for overlay reachability separate from IPv4 unicast NLRI. The observed evidence is decisive here because the EVPN BGP table contains expected Type 2 and Type 3 routes without changing the underlay protocol. The Juniper control here is “Remote MAC tables point to the new VTEP and traffic follows the migrated host without persistent blackholes”, supported by this specific technical distinction: EVPN MAC mobility conveys a change of host location so remote VTEPs update forwarding. The observed evidence is decisive here because remote MAC tables point to the new VTEP and traffic follows the migrated host without persistent blackholes.
D:
“A controlled leaf failure preserves tenant reachability through the remaining advertised EVPN path” is relevant when eVPN multihoming resiliency depends on correct Ethernet-segment signaling and reachable surviving VTEPs. The observed evidence is decisive here because a controlled leaf failure preserves tenant reachability through the remaining advertised EVPN path. The Juniper control here is “Remote MAC tables point to the new VTEP and traffic follows the migrated host without persistent blackholes”, supported by this specific technical distinction: EVPN MAC mobility conveys a change of host location so remote VTEPs update forwarding. The observed evidence is decisive here because remote MAC tables point to the new VTEP and traffic follows the migrated host without persistent blackholes.
Question 393
The deployment requirement is as follows: A host MAC appears behind two unrelated EVPN leaves simultaneously and an operator assumes this is harmless load balancing. Which solution fits the stated constraint?
Restore underlay IP reachability and correct next-hop resolution to the remote VTEP address.
Investigate duplicate-MAC detection and verify whether any move is legitimate before allowing competing advertisements.
Enable supported BGP EVPN signaling family between the intended route peers with necessary import/export policy.
Validate the Ethernet-segment designated-forwarder election and per-VLAN or EVI forwarding role.
Explanation
Correct Answer
B:
A MAC learned at contradictory non-multihomed locations can signal a loop or duplicate identity. The specifically applicable intervention is: Investigate duplicate-MAC detection and verify whether any move is legitimate before allowing competing advertisements. A discriminating confirmation would be: Duplicate-MAC alarms clear after removing the unintended attachment and one authorized MAC location remains.
Incorrect Answers
A:
“Restore underlay IP reachability and correct next-hop resolution to the remote VTEP address” is relevant when eVPN control-plane learning does not replace underlay IP transport to the VTEP next hop. The Juniper control here is “Investigate duplicate-MAC detection and verify whether any move is legitimate before allowing competing advertisements”, supported by this specific technical distinction: A MAC learned at contradictory non-multihomed locations can signal a loop or duplicate identity.
C:
“Enable supported BGP EVPN signaling family between the intended route peers with necessary import/export policy” is relevant when eVPN uses its own BGP address family for overlay reachability separate from IPv4 unicast NLRI. The Juniper control here is “Investigate duplicate-MAC detection and verify whether any move is legitimate before allowing competing advertisements”, supported by this specific technical distinction: A MAC learned at contradictory non-multihomed locations can signal a loop or duplicate identity.
D:
“Validate the Ethernet-segment designated-forwarder election and per-VLAN or EVI forwarding role” is relevant when eVPN designated forwarder selection prevents duplicate BUM delivery on all-active multihomed segments. The Juniper control here is “Investigate duplicate-MAC detection and verify whether any move is legitimate before allowing competing advertisements”, supported by this specific technical distinction: A MAC learned at contradictory non-multihomed locations can signal a loop or duplicate identity.
Question 394
A technician has completed this work: Investigate duplicate-MAC detection and verify whether any move is legitimate before allowing competing advertisements. Which post-change observation most directly validates it?
The EVPN BGP table contains expected Type 2 and Type 3 routes without changing the underlay protocol.
Remote MAC tables point to the new VTEP and traffic follows the migrated host without persistent blackholes.
A target-specific route check shows Tenant A MAC routes only in Tenant A's EVPN instance.
Duplicate-MAC alarms clear after removing the unintended attachment and one authorized MAC location remains.
Explanation
Correct Answer
D:
A MAC learned at contradictory non-multihomed locations can signal a loop or duplicate identity. The observed evidence is decisive here because duplicate-MAC alarms clear after removing the unintended attachment and one authorized MAC location remains. This tests the actual EVPN duplicate MAC condition rather than an unrelated operational symptom.
Incorrect Answers
A:
“The EVPN BGP table contains expected Type 2 and Type 3 routes without changing the underlay protocol” is relevant when eVPN uses its own BGP address family for overlay reachability separate from IPv4 unicast NLRI. The observed evidence is decisive here because the EVPN BGP table contains expected Type 2 and Type 3 routes without changing the underlay protocol. The Juniper control here is “Duplicate-MAC alarms clear after removing the unintended attachment and one authorized MAC location remains”, supported by this specific technical distinction: A MAC learned at contradictory non-multihomed locations can signal a loop or duplicate identity. The observed evidence is decisive here because duplicate-MAC alarms clear after removing the unintended attachment and one authorized MAC location remains.
B:
“Remote MAC tables point to the new VTEP and traffic follows the migrated host without persistent blackholes” is relevant when eVPN MAC mobility conveys a change of host location so remote VTEPs update forwarding. The observed evidence is decisive here because remote MAC tables point to the new VTEP and traffic follows the migrated host without persistent blackholes. The Juniper control here is “Duplicate-MAC alarms clear after removing the unintended attachment and one authorized MAC location remains”, supported by this specific technical distinction: A MAC learned at contradictory non-multihomed locations can signal a loop or duplicate identity. The observed evidence is decisive here because duplicate-MAC alarms clear after removing the unintended attachment and one authorized MAC location remains.
C:
“A target-specific route check shows Tenant A MAC routes only in Tenant A's EVPN instance” is relevant when eVPN route targets govern which VPN instances import a route, independently of the host's MAC itself. The observed evidence is decisive here because a target-specific route check shows Tenant A MAC routes only in Tenant A's EVPN instance. The Juniper control here is “Duplicate-MAC alarms clear after removing the unintended attachment and one authorized MAC location remains”, supported by this specific technical distinction: A MAC learned at contradictory non-multihomed locations can signal a loop or duplicate identity. The observed evidence is decisive here because duplicate-MAC alarms clear after removing the unintended attachment and one authorized MAC location remains.
Question 395
A Junos administrator observes: Underlay OSPF and IP reachability are healthy, but EVPN MAC routes never appear because only BGP inet-unicast was enabled. Which technical adjustment is most appropriate?
Restore underlay IP reachability and correct next-hop resolution to the remote VTEP address.
Trace EVPN MAC mobility sequence signaling and withdraw or supersede obsolete Type 2 MAC routes.
Correct EVPN import/export extended route-target membership per tenant EVI.
Enable supported BGP EVPN signaling family between the intended route peers with necessary import/export policy.
Explanation
Correct Answer
D:
EVPN uses its own BGP address family for overlay reachability separate from IPv4 unicast NLRI. The specifically applicable intervention is: Enable supported BGP EVPN signaling family between the intended route peers with necessary import/export policy. A discriminating confirmation would be: The EVPN BGP table contains expected Type 2 and Type 3 routes without changing the underlay protocol.
Incorrect Answers
A:
“Restore underlay IP reachability and correct next-hop resolution to the remote VTEP address” is relevant when eVPN control-plane learning does not replace underlay IP transport to the VTEP next hop. The Juniper control here is “Enable supported BGP EVPN signaling family between the intended route peers with necessary import/export policy”, supported by this specific technical distinction: EVPN uses its own BGP address family for overlay reachability separate from IPv4 unicast NLRI.
B:
“Trace EVPN MAC mobility sequence signaling and withdraw or supersede obsolete Type 2 MAC routes” is relevant when eVPN MAC mobility conveys a change of host location so remote VTEPs update forwarding. The Juniper control here is “Enable supported BGP EVPN signaling family between the intended route peers with necessary import/export policy”, supported by this specific technical distinction: EVPN uses its own BGP address family for overlay reachability separate from IPv4 unicast NLRI.
C:
“Correct EVPN import/export extended route-target membership per tenant EVI” is relevant when eVPN route targets govern which VPN instances import a route, independently of the host's MAC itself. The Juniper control here is “Enable supported BGP EVPN signaling family between the intended route peers with necessary import/export policy”, supported by this specific technical distinction: EVPN uses its own BGP address family for overlay reachability separate from IPv4 unicast NLRI.
Question 396
The approved intervention was: Enable supported BGP EVPN signaling family between the intended route peers with necessary import/export policy. What observable outcome would show that it addressed the original issue?
A VTEP reachability test succeeds and VXLAN data packets arrive at the remote leaf.
The EVPN BGP table contains expected Type 2 and Type 3 routes without changing the underlay protocol.
Remote MAC tables point to the new VTEP and traffic follows the migrated host without persistent blackholes.
The remote EVPN MAC table learns the advertised host MAC with the correct remote VTEP next hop.
Explanation
Correct Answer
B:
EVPN uses its own BGP address family for overlay reachability separate from IPv4 unicast NLRI. The observed evidence is decisive here because the EVPN BGP table contains expected Type 2 and Type 3 routes without changing the underlay protocol. This tests the actual EVPN control family condition rather than an unrelated operational symptom.
Incorrect Answers
A:
“A VTEP reachability test succeeds and VXLAN data packets arrive at the remote leaf” is relevant when eVPN control-plane learning does not replace underlay IP transport to the VTEP next hop. The observed evidence is decisive here because a VTEP reachability test succeeds and VXLAN data packets arrive at the remote leaf. The Juniper control here is “The EVPN BGP table contains expected Type 2 and Type 3 routes without changing the underlay protocol”, supported by this specific technical distinction: EVPN uses its own BGP address family for overlay reachability separate from IPv4 unicast NLRI. The observed evidence is decisive here because the EVPN BGP table contains expected Type 2 and Type 3 routes without changing the underlay protocol.
C:
“Remote MAC tables point to the new VTEP and traffic follows the migrated host without persistent blackholes” is relevant when eVPN MAC mobility conveys a change of host location so remote VTEPs update forwarding. The observed evidence is decisive here because remote MAC tables point to the new VTEP and traffic follows the migrated host without persistent blackholes. The Juniper control here is “The EVPN BGP table contains expected Type 2 and Type 3 routes without changing the underlay protocol”, supported by this specific technical distinction: EVPN uses its own BGP address family for overlay reachability separate from IPv4 unicast NLRI. The observed evidence is decisive here because the EVPN BGP table contains expected Type 2 and Type 3 routes without changing the underlay protocol.
D:
“The remote EVPN MAC table learns the advertised host MAC with the correct remote VTEP next hop” is relevant when eVPN Type 2 BGP routes distribute host MAC and optional IP bindings in the overlay control plane. The observed evidence is decisive here because the remote EVPN MAC table learns the advertised host MAC with the correct remote VTEP next hop. The Juniper control here is “The EVPN BGP table contains expected Type 2 and Type 3 routes without changing the underlay protocol”, supported by this specific technical distinction: EVPN uses its own BGP address family for overlay reachability separate from IPv4 unicast NLRI. The observed evidence is decisive here because the EVPN BGP table contains expected Type 2 and Type 3 routes without changing the underlay protocol.
Question 397
An operator documents this Junos scenario: Tenant A's MAC routes leak into Tenant B's EVPN instance after a route-target policy template change. Which response should be prioritized?
Confirm EVPN Type 2 MAC/IP route advertisement and import policy for the host's VLAN/VNI.
Investigate duplicate-MAC detection and verify whether any move is legitimate before allowing competing advertisements.
Align approved VLAN-to-VNI mappings and associated EVPN instance policy across the tenant leafs.
Correct EVPN import/export extended route-target membership per tenant EVI.
Explanation
Correct Answer
D:
EVPN route targets govern which VPN instances import a route, independently of the host's MAC itself. The specifically applicable intervention is: Correct EVPN import/export extended route-target membership per tenant EVI. A discriminating confirmation would be: A target-specific route check shows Tenant A MAC routes only in Tenant A's EVPN instance.
Incorrect Answers
A:
“Confirm EVPN Type 2 MAC/IP route advertisement and import policy for the host's VLAN/VNI” is relevant when eVPN Type 2 BGP routes distribute host MAC and optional IP bindings in the overlay control plane. The Juniper control here is “Correct EVPN import/export extended route-target membership per tenant EVI”, supported by this specific technical distinction: EVPN route targets govern which VPN instances import a route, independently of the host's MAC itself.
B:
“Investigate duplicate-MAC detection and verify whether any move is legitimate before allowing competing advertisements” is relevant when a MAC learned at contradictory non-multihomed locations can signal a loop or duplicate identity. The Juniper control here is “Correct EVPN import/export extended route-target membership per tenant EVI”, supported by this specific technical distinction: EVPN route targets govern which VPN instances import a route, independently of the host's MAC itself.
C:
“Align approved VLAN-to-VNI mappings and associated EVPN instance policy across the tenant leafs” is relevant when the VXLAN VNI identifies the overlay broadcast domain and must map consistently for tenant bridging. The Juniper control here is “Correct EVPN import/export extended route-target membership per tenant EVI”, supported by this specific technical distinction: EVPN route targets govern which VPN instances import a route, independently of the host's MAC itself.
Question 398
The site applied this change: Correct EVPN import/export extended route-target membership per tenant EVI. What check most directly verifies the intended result?
Duplicate-MAC alarms clear after removing the unintended attachment and one authorized MAC location remains.
A target-specific route check shows Tenant A MAC routes only in Tenant A's EVPN instance.
Remote VTEPs join the appropriate BUM replication set and ARP requests reach the intended VLAN segments.
Remote MAC tables point to the new VTEP and traffic follows the migrated host without persistent blackholes.
Explanation
Correct Answer
B:
EVPN route targets govern which VPN instances import a route, independently of the host's MAC itself. The observed evidence is decisive here because a target-specific route check shows Tenant A MAC routes only in Tenant A's EVPN instance. This tests the actual EVPN route target condition rather than an unrelated operational symptom.
Incorrect Answers
A:
“Duplicate-MAC alarms clear after removing the unintended attachment and one authorized MAC location remains” is relevant when a MAC learned at contradictory non-multihomed locations can signal a loop or duplicate identity. The observed evidence is decisive here because duplicate-MAC alarms clear after removing the unintended attachment and one authorized MAC location remains. The Juniper control here is “A target-specific route check shows Tenant A MAC routes only in Tenant A's EVPN instance”, supported by this specific technical distinction: EVPN route targets govern which VPN instances import a route, independently of the host's MAC itself. The observed evidence is decisive here because a target-specific route check shows Tenant A MAC routes only in Tenant A's EVPN instance.
C:
“Remote VTEPs join the appropriate BUM replication set and ARP requests reach the intended VLAN segments” is relevant when eVPN Type 3 routes support discovery of VTEPs participating in broadcast, unknown-unicast and multicast distribution. The observed evidence is decisive here because remote VTEPs join the appropriate BUM replication set and ARP requests reach the intended VLAN segments. The Juniper control here is “A target-specific route check shows Tenant A MAC routes only in Tenant A's EVPN instance”, supported by this specific technical distinction: EVPN route targets govern which VPN instances import a route, independently of the host's MAC itself. The observed evidence is decisive here because a target-specific route check shows Tenant A MAC routes only in Tenant A's EVPN instance.
D:
“Remote MAC tables point to the new VTEP and traffic follows the migrated host without persistent blackholes” is relevant when eVPN MAC mobility conveys a change of host location so remote VTEPs update forwarding. The observed evidence is decisive here because remote MAC tables point to the new VTEP and traffic follows the migrated host without persistent blackholes. The Juniper control here is “A target-specific route check shows Tenant A MAC routes only in Tenant A's EVPN instance”, supported by this specific technical distinction: EVPN route targets govern which VPN instances import a route, independently of the host's MAC itself. The observed evidence is decisive here because a target-specific route check shows Tenant A MAC routes only in Tenant A's EVPN instance.
Question 399
A network review identifies: An EVPN VXLAN fabric is described as dual-homed but losing one leaf causes a long outage even though the second link is up. Which action best addresses the root issue?
Validate the Ethernet-segment designated-forwarder election and per-VLAN or EVI forwarding role.
Confirm EVPN Type 2 MAC/IP route advertisement and import policy for the host's VLAN/VNI.
Check ESI multihoming state, Type 1 withdrawal, surviving Type 2 routes and underlay next-hop convergence.
Restore supported EVPN Type 3 inclusive-multicast route exchange and replication-list membership.
Explanation
Correct Answer
C:
EVPN multihoming resiliency depends on correct Ethernet-segment signaling and reachable surviving VTEPs. The specifically applicable intervention is: Check ESI multihoming state, Type 1 withdrawal, surviving Type 2 routes and underlay next-hop convergence. A discriminating confirmation would be: A controlled leaf failure preserves tenant reachability through the remaining advertised EVPN path.
Incorrect Answers
A:
“Validate the Ethernet-segment designated-forwarder election and per-VLAN or EVI forwarding role” is relevant when eVPN designated forwarder selection prevents duplicate BUM delivery on all-active multihomed segments. The Juniper control here is “Check ESI multihoming state, Type 1 withdrawal, surviving Type 2 routes and underlay next-hop convergence”, supported by this specific technical distinction: EVPN multihoming resiliency depends on correct Ethernet-segment signaling and reachable surviving VTEPs.
B:
“Confirm EVPN Type 2 MAC/IP route advertisement and import policy for the host's VLAN/VNI” is relevant when eVPN Type 2 BGP routes distribute host MAC and optional IP bindings in the overlay control plane. The Juniper control here is “Check ESI multihoming state, Type 1 withdrawal, surviving Type 2 routes and underlay next-hop convergence”, supported by this specific technical distinction: EVPN multihoming resiliency depends on correct Ethernet-segment signaling and reachable surviving VTEPs.
D:
“Restore supported EVPN Type 3 inclusive-multicast route exchange and replication-list membership” is relevant when eVPN Type 3 routes support discovery of VTEPs participating in broadcast, unknown-unicast and multicast distribution. The Juniper control here is “Check ESI multihoming state, Type 1 withdrawal, surviving Type 2 routes and underlay next-hop convergence”, supported by this specific technical distinction: EVPN multihoming resiliency depends on correct Ethernet-segment signaling and reachable surviving VTEPs.
Question 400
To verify the repair, assess this original condition: An EVPN VXLAN fabric is described as dual-homed but losing one leaf causes a long outage even though the second link is up. Which test outcome best proves success?
Remote VTEPs join the appropriate BUM replication set and ARP requests reach the intended VLAN segments.
The remote EVPN MAC table learns the advertised host MAC with the correct remote VTEP next hop.
Only the elected DF forwards BUM traffic toward the shared segment while the other peer remains standby for that function.
A controlled leaf failure preserves tenant reachability through the remaining advertised EVPN path.
Explanation
Correct Answer
D:
EVPN multihoming resiliency depends on correct Ethernet-segment signaling and reachable surviving VTEPs. The observed evidence is decisive here because a controlled leaf failure preserves tenant reachability through the remaining advertised EVPN path. This tests the actual EVPN failover validation condition rather than an unrelated operational symptom.
Incorrect Answers
A:
“Remote VTEPs join the appropriate BUM replication set and ARP requests reach the intended VLAN segments” is relevant when eVPN Type 3 routes support discovery of VTEPs participating in broadcast, unknown-unicast and multicast distribution. The observed evidence is decisive here because remote VTEPs join the appropriate BUM replication set and ARP requests reach the intended VLAN segments. The Juniper control here is “A controlled leaf failure preserves tenant reachability through the remaining advertised EVPN path”, supported by this specific technical distinction: EVPN multihoming resiliency depends on correct Ethernet-segment signaling and reachable surviving VTEPs. The observed evidence is decisive here because a controlled leaf failure preserves tenant reachability through the remaining advertised EVPN path.
B:
“The remote EVPN MAC table learns the advertised host MAC with the correct remote VTEP next hop” is relevant when eVPN Type 2 BGP routes distribute host MAC and optional IP bindings in the overlay control plane. The observed evidence is decisive here because the remote EVPN MAC table learns the advertised host MAC with the correct remote VTEP next hop. The Juniper control here is “A controlled leaf failure preserves tenant reachability through the remaining advertised EVPN path”, supported by this specific technical distinction: EVPN multihoming resiliency depends on correct Ethernet-segment signaling and reachable surviving VTEPs. The observed evidence is decisive here because a controlled leaf failure preserves tenant reachability through the remaining advertised EVPN path.
C:
“Only the elected DF forwards BUM traffic toward the shared segment while the other peer remains standby for that function” is relevant when eVPN designated forwarder selection prevents duplicate BUM delivery on all-active multihomed segments. The observed evidence is decisive here because only the elected DF forwards BUM traffic toward the shared segment while the other peer remains standby for that function. The Juniper control here is “A controlled leaf failure preserves tenant reachability through the remaining advertised EVPN path”, supported by this specific technical distinction: EVPN multihoming resiliency depends on correct Ethernet-segment signaling and reachable surviving VTEPs. The observed evidence is decisive here because a controlled leaf failure preserves tenant reachability through the remaining advertised EVPN path.
Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests
Our team works hard to provide students with high exam practice test questions and compelling learning experiences. We're confident of the quality level of the products we offer and provide no hassle satisfaction guarantee.
Why choose Exam-Labs?613,692+Satisfied Customers since 2015
100% Latest Exam Questions
Accurate & Updated Answers
Regular Free Updates
24/7 Customer Support
Instant Download
Exam Info
Juniper JN0-650 Practice Test Questions, Juniper JN0-650 Exam Practice Test Questions
Looking to pass your tests the first time. You can study with Juniper JN0-650 certification practice test questions and answers, study guide, training courses. With Exam-Labs VCE files you can prepare with Juniper JN0-650 Enterprise Routing and Switching, Professional (JNCIP-ENT) exam practice test questions and answers. The most complete solution for passing with Juniper certification JN0-650 exam practice test questions and answers, study guide, training course.
JN0-650 Enterprise Routing and Switching, Professional
JN0-650 is the current Juniper Enterprise Routing and Switching, Professional exam for JNCIP-ENT as of October 2026. It launched on November 10, 2025 after JN0-649 reached end of life on November 9.
Juniper lists 65 multiple-choice questions, a 90-minute test window, Pearson VUE delivery, and JNCIS-ENT as the prerequisite certification. The live blueprint identifies Junos OS 25.2 and covers advanced enterprise routing, multicast, switching and access control, IP telephony features, class of service, and EVPN.
The exam rewards candidates who can reason across protocol layers. A professional engineer must understand not only how to configure OSPF, BGP, authentication, QoS, or EVPN, but how those systems interact when a campus or enterprise network changes state.
Route-policy reasoning is more important than memorizing protocol defaults
JN0-650-level routing questions often present several valid routes and ask candidates to determine which one should be active or advertised. Build a habit of separating protocol knowledge from policy. First identify what each protocol learned, then apply the routing-policy decision, then determine the resulting forwarding choice.
Use a multi-path lab and deliberately change one preference, metric, or policy attribute at a time. Predict the outcome before checking the router. This creates a strong mental model of route selection and makes later troubleshooting much more systematic.
The active JNCIA-Junos foundation and JN0-106 concepts remain relevant because advanced policy still depends on precise understanding of Junos routing and configuration behavior.
OSPF troubleshooting should move from adjacency to database to route
A neighbor in Full state proves only part of the control plane. A professional candidate should check which LSAs exist, how area boundaries affect propagation, what the shortest-path calculation produces, and whether policy or preference changes the final route.
Build a topology with at least two areas and redundant paths. Change an interface cost, summarize a prefix, or remove a link. Predict the LSA and route changes, then verify them. This trains candidates to explain the cause of a route change rather than merely observe that the table changed.
BGP becomes an enterprise tool when policy expresses path preference
Professional BGP study should include import and export policy, communities, path attributes, route reflection or internal distribution considerations, and careful verification of what a peer actually receives. A route being present in one table does not guarantee that it is active or exported.
Create a scenario with two upstream paths and a set of prefixes that should prefer different exits. Use policy to express that intention, then inspect received, active, and advertised routes. Add a failure and confirm whether the design falls back as expected.
The core concepts in Border Gateway Protocol remain useful, but the professional skill is using those concepts to make predictable policy decisions under changing topology.
Multicast forwarding depends on correct unicast reachability and receiver state
Multicast troubleshooting requires candidates to track multiple forms of state at once. Receiver membership, source reachability, rendezvous-point behavior, reverse-path forwarding checks, and multicast forwarding entries all contribute to whether traffic reaches a listener.
Use a lab where unicast routing changes without modifying multicast configuration. Observe how the multicast tree reacts. This demonstrates why professional engineers cannot isolate multicast from the underlying routing design.
When using rendezvous-point models, multicast RP concepts provide useful context for understanding shared trees and the control-plane decisions behind them.
Layer 2 access control should be tested under authentication failure
The current enterprise blueprint includes 802.1X, MAC RADIUS, guest behavior, fallback, and the use of multiple access-control methods. Candidates should understand the normal authentication flow and the failure states that determine what a device can do when identity services are unavailable.
Build three endpoint cases: a normal supplicant, a device that uses MAC-based authentication, and a device that fails authentication. Observe assigned VLANs or roles, RADIUS exchanges, and switch state. Then fail the authentication server and verify the configured fallback behavior.
802.1X is the core protocol reference, but JN0-650 preparation should focus on operational outcomes and how access policy interacts with the rest of the campus network.
Voice services demonstrate why enterprise switching is application infrastructure
PoE, LLDP-MED, and voice VLANs are included because campus switches deliver more than generic Ethernet connectivity. A phone depends on power, discovery, segmentation, addressing, and often traffic prioritization. Each dependency can create a different symptom.
Trace a phone boot process from power negotiation through VLAN discovery and network registration. Add a workstation behind the phone and verify that voice and data traffic follow the intended segmentation. This is an efficient way to connect multiple switching features in one scenario.
The larger lesson is that configuration should be evaluated by service behavior. A correct-looking interface is not enough if the endpoint receives the wrong policy or cannot reach required services.
Class of service should be verified under congestion
Classification, forwarding classes, loss priority, policers, schedulers, drop profiles, shaping, and rewrite rules are meaningful only when traffic competes for limited resources. JN0-650 candidates should be able to explain how packets move from classification to queue treatment and what happens when a queue fills.
Generate competing traffic classes and observe queue counters, drops, and latency. Change one scheduler or policer value and predict the effect. This turns QoS from a list of configuration knobs into an operational model.
The broader principles of quality of service provide useful context for why classification and scheduling exist and how they protect delay-sensitive applications.
EVPN and VXLAN connect modern campus design to BGP control-plane skills
EVPN uses BGP to distribute endpoint and segment information, while VXLAN provides the overlay encapsulation across an IP underlay. JN0-650 candidates should understand route types, VTEPs, multihoming, and the relationship between control-plane reachability and data-plane forwarding.
Draw a two-leaf fabric and trace one host-to-host flow. Identify where MAC information is learned, which EVPN information is advertised, how the destination VTEP is selected, and which underlay route carries the VXLAN packet. Then fail a multihomed link and observe convergence.
The detailed explanation of VXLAN is useful when separating encapsulation behavior from the EVPN control plane.
Professional preparation should combine protocols in the same failure domain
Do not finish studying each objective in isolation. Build integrated scenarios where a route-policy change affects multicast reachability, an authentication failure places a user into a different segment, QoS changes voice performance, or an EVPN fabric failure alters the path used by campus services.
For every incident, write the expected control-plane state, forwarding state, and user-visible symptom before troubleshooting. Then prove or disprove the hypothesis with device evidence. This creates the kind of cross-domain reasoning that separates professional-level knowledge from command familiarity.
As of October 2026, JN0-650 is the live exam. Verify the current Juniper blueprint and Junos version before scheduling, and use JN0-649 material only where it still supports the current objectives.
A strong integrated lab can use the same endpoint and application flows to test several objectives. Place users behind authenticated switch ports, route traffic through an OSPF campus, use BGP at the external edge, and carry one segment through EVPN-VXLAN. Add a voice endpoint with a separate class-of-service requirement. This gives the learner a single environment where changes in one control plane create measurable effects elsewhere.
For example, modify an OSPF metric and observe whether the BGP next hop remains reachable; change a RADIUS condition and verify the endpoint's resulting segment; alter a queue scheduler and measure the effect on voice traffic during congestion; withdraw an EVPN route and confirm that the underlay can still reach the remote VTEP even though the overlay service is unavailable. Each case reinforces the difference between infrastructure health and service health.
Candidates should also practice reading operational output with a question in mind. Do not dump every protocol command and search for something unusual. Ask which state would confirm or disprove the hypothesis, then inspect that state. This reduces noise and mirrors how professional engineers work during outages.
As the live exam evolves, keep a small versioned study sheet that records the current exam code, prerequisite, software version, and objective headings separately from personal protocol notes. When Juniper updates the certification, only the versioned layer needs immediate review; the deeper routing and switching knowledge remains reusable.
During final review, build a compact evidence matrix. For each major objective, list the most useful operational proof: OSPF database and route state, BGP received and advertised routes, authentication and RADIUS state, queue counters for QoS, and EVPN routes plus VTEP reachability for overlays. This prevents troubleshooting from becoming a command-memory contest.
The matrix also improves exam pacing. When a scenario describes one specific symptom, candidates can mentally jump to the small set of states that would explain it, eliminate answers that target unrelated layers, and choose the action that tests the most likely dependency first. That is professional troubleshooting logic, not merely certification technique.
Before scheduling, run the integrated topology from a clean build and recover it from at least two failures without referring to step-by-step notes. That final exercise tests whether protocol relationships have become usable knowledge rather than remembered procedure, and it exposes weak areas while there is still time to review them.
Use Juniper JN0-650 certification exam practice test questions, study guide and training course - the complete package at discounted price. Pass with JN0-650 Enterprise Routing and Switching, Professional (JNCIP-ENT) practice test questions and answers, study guide, complete training course especially formatted in VCE files. Latest Juniper certification JN0-650 exam practice test questions and answers will guarantee your success without studying for endless hours.
FAQs
Juniper JN0-650 Exam Practice Test Questions, Juniper JN0-650 Practice Test Questions and Answers
Do you have questions about our JN0-650 Enterprise Routing and Switching, Professional (JNCIP-ENT) practice test questions and answers or any of our products? If you are not clear about our Juniper JN0-650 exam practice test questions, you can read the FAQ below.
The JN0-650 Premium File has been developed by industry professionals, who have been working with IT certifications for years and have close ties with IT certification vendors and holders - with most recent exam questions and valid answers.
JN0-650 Premium File is presented in VCE format. VCE (Virtual CertExam) is a file format that realistically simulates JN0-650 exam environment, allowing for the most convenient exam preparation you can get - in the convenience of your own home or on the go. If you have ever seen IT exam simulations, chances are, they were in the VCE format.
What is VCE?
VCE is a file format associated with Visual CertExam Software. This format and software are widely used for creating tests for IT certifications. To create and open VCE files, you will need to purchase, download and install VCE Exam Simulator on your computer.
Can I try it for free?
Yes, you can. Look through free VCE files section and download any file you choose absolutely free.
Where do I get VCE Exam Simulator?
VCE Exam Simulator can be purchased from its developer, https://www.avanset.com. Please note that Exam-Labs does not sell or support this software. Should you have any questions or concerns about using this product, please contact Avanset support team directly.
How are Premium VCE files different from Free VCE files?
Premium VCE files have been developed by industry professionals, who have been working with IT certifications for years and have close ties with IT certification vendors and holders - with most recent exam questions and some insider information.
Free VCE files All files are sent by Exam-labs community members. We encourage everyone who has recently taken an exam and/or has come across some braindumps that have turned out to be true to share this information with the community by creating and sending VCE files. We don't say that these free VCEs sent by our members aren't reliable (experience shows that they are). But you should use your critical thinking as to what you download and memorize.
How long will I receive updates for JN0-650 Premium VCE File that I purchased?
Free updates are available during 30 days after you purchased Premium VCE file. After 30 days the file will become unavailable.
How can I get the products after purchase?
All products are available for download immediately from your Member's Area. Once you have made the payment, you will be transferred to Member's Area where you can login and download the products you have purchased to your PC or another device.
Will I be able to renew my products when they expire?
Yes, when the 30 days of your product validity are over, you have the option of renewing your expired products with a 30% discount. This can be done in your Member's Area.
Please note that you will not be able to use the product after it has expired if you don't renew it.
How often are the questions updated?
We always try to provide the latest pool of questions, Updates in the questions depend on the changes in actual pool of questions by different vendors. As soon as we know about the change in the exam question pool we try our best to update the products as fast as possible.
What is a Study Guide?
Study Guides available on Exam-Labs are built by industry professionals who have been working with IT certifications for years. Study Guides offer full coverage on exam objectives in a systematic approach. Study Guides are very useful for fresh applicants and provides background knowledge about preparation of exams.
How can I open a Study Guide?
Any study guide can be opened by an official Acrobat by Adobe or any other reader application you use.
What is a Training Course?
Training Courses we offer on Exam-Labs in video format are created and managed by IT professionals. The foundation of each course are its lectures, which can include videos, slides and text. In addition, authors can add resources and various types of practice activities, as a way to enhance the learning experience of students.
Enter Your Email Address to Proceed
Please fill out your email address below in order to purchase Certification/Exam.
Enter Your Email Address to Proceed
Please fill out your email address below in order to purchase Demo.
How It Works
Step 1. Choose Exam on Exam-Labs
Download IT Exams Questions & Answers
Step 2. Open Exam with Avanset Exam Simulator
Press here to download VCE Exam Simulator that simulates latest exam environment