Includes questions types found on actual exam such as drag and drop, simulation, type in, and fill in the blank.
Service Provider Routing and Switching, Specialist (JNCIS-SP) JN0-364 Practice Test 21
Question 200
For fictional Bluehaven Edge, identify the shortcut that fails to address: Two routes learned from different upstream providers have comparable reachability, but outbound traffic follows the less-preferred contract.
Change remote MED attributes on unrelated inbound routes and assume local preference is unaffected.
Remove all outbound BGP filtering to increase prefix visibility during troubleshooting.
Advertise arbitrary prefixes to the loopback peer without configuring required transport reachability or multihop.
Increase BGP route preference without checking the ASN carried by the remote peer.
Explanation
Correct Answer
A:
Reject this option for the observed incident at Bluehaven Edge: Two routes learned from different upstream providers have comparable reachability, but outbound traffic follows the less-preferred contract. Use instead: Adjust the internal local-preference policy for the desired upstream while checking for higher-priority selection constraints.
Incorrect Answers
B:
This alternative is problematic for BGP outbound prefix leak, rather than the reported BGP local preference egress selection. Corrective action here is: Adjust the internal local-preference policy for the desired upstream while checking for higher-priority selection constraints.
C:
This shortcut would also be unsafe, but for a different BGP multihop design case (Two loopback-sourced eBGP peers separated by multiple routed hops cannot connect although their loopbacks are mutually reachable.). It does not repeat the defect in this question: The provider's internal BGP policy assigns local preference values inconsistent with the intended egress decision.
D:
The proposal recreates the separate BGP AS number mismatch error. The current case instead concerns: Two routes learned from different upstream providers have comparable reachability, but outbound traffic follows the less-preferred contract. Its specific failed assumption is: The provider's internal BGP policy assigns local preference values inconsistent with the intended egress decision.
Question 201
At fictional Stonebridge ISP (regional ISP), this Junos network defect is reported: An operator expects a lower MED to override a higher local preference when choosing between multiple BGP paths. What should the specialist change first?
Check the relevant RIB, current peer advertisements and route withdrawal state before deleting configurations.
Implement or validate an authorized route-reflector design or required iBGP peering while preserving loop controls.
Inspect show bgp neighbor detail, last error and state transitions before modifying attributes or policies.
Inspect best-path criteria in order and use approved local preference for intra-AS outbound selection before evaluating MED.
Explanation
Correct Answer
D:
Correct because the observable problem is: An operator expects a lower MED to override a higher local preference when choosing between multiple BGP paths. Use the controlled remedy: Inspect best-path criteria in order and use approved local preference for intra-AS outbound selection before evaluating MED. Confirm the resulting state with: Chosen paths match the configured local-preference intent and MED is considered only where applicable in the selection order.
Incorrect Answers
A:
Although relevant to BGP withdraw failure interpretation, this configuration does not remedy the reported BGP MED conditional comparison failure. Use: Inspect best-path criteria in order and use approved local preference for intra-AS outbound selection before evaluating MED.
B:
That action would address the separate IBGP split horizon route reflector case, where An internal BGP speaker learns a prefix from one iBGP peer but does not re-advertise it to another ordinary iBGP peer. The present BGP MED conditional comparison issue instead requires: Inspect best-path criteria in order and use approved local preference for intra-AS outbound selection before evaluating MED.
C:
The proposal is a correction for BGP notification diagnostics, not this situation: An operator expects a lower MED to override a higher local preference when choosing between multiple BGP paths. Here the cause is: The decision assumes MED outranks local preference in the BGP selection process, which is not generally correct.
Question 202
A Junos routing specialist investigates at fictional Stonebridge ISP: An operator expects a lower MED to override a higher local preference when choosing between multiple BGP paths. What control gap requires attention?
A neighbor-level configuration overrides the intended group-level export policy for that session.
A stale or alternate-table record is being conflated with active accepted and currently advertised BGP reachability.
The decision assumes MED outranks local preference in the BGP selection process, which is not generally correct.
The configured peer AS no longer matches the actual remote AS used in the BGP OPEN exchange.
Explanation
Correct Answer
C:
Fictional Stonebridge ISP demonstrates this underlying defect: The decision assumes MED outranks local preference in the BGP selection process, which is not generally correct. Validate after remediation by checking: Chosen paths match the configured local-preference intent and MED is considered only where applicable in the selection order.
Incorrect Answers
A:
That diagnosis belongs to BGP peer group inheritance, for example: One member of a BGP group has a peer-specific outbound policy override and advertises a different set of prefixes than sibling peers. It does not explain this case, which is caused by: The decision assumes MED outranks local preference in the BGP selection process, which is not generally correct.
B:
The alternate cause would explain BGP withdraw failure interpretation. For BGP MED conditional comparison at Stonebridge ISP, the evidence instead supports: The decision assumes MED outranks local preference in the BGP selection process, which is not generally correct.
D:
That diagnosis belongs to BGP AS number mismatch, for example: Two eBGP neighbors have IP connectivity but the session never progresses to Established after the remote carrier changes its autonomous system number. It does not explain this case, which is caused by: The decision assumes MED outranks local preference in the BGP selection process, which is not generally correct.
Question 203
Following remediation at fictional Stonebridge ISP, how should the team verify that this specific issue is resolved? An operator expects a lower MED to override a higher local preference when choosing between multiple BGP paths.
The intended internal clients learn the prefix through the approved reflection or full-mesh topology.
Chosen paths match the configured local-preference intent and MED is considered only where applicable in the selection order.
The external peer receives only the authorized prefixes and no internal management route.
The selected BGP path uses the intended provider across internal routers without affecting received prefix filtering.
Explanation
Correct Answer
B:
Sign-off requires case-specific evidence: Chosen paths match the configured local-preference intent and MED is considered only where applicable in the selection order. Without that observation, the decision assumes med outranks local preference in the bgp selection process, which is not generally correct.
Incorrect Answers
A:
This observation is appropriate for IBGP split horizon route reflector, not the BGP MED conditional comparison defect at Stonebridge ISP. Verify instead: Chosen paths match the configured local-preference intent and MED is considered only where applicable in the selection order.
C:
That result would validate the separate BGP outbound prefix leak scenario (A provider edge advertises an internal management subnet to an external customer after a new export-policy term is inserted.). It does not prove the needed BGP MED conditional comparison outcome: Chosen paths match the configured local-preference intent and MED is considered only where applicable in the selection order.
D:
This observation is appropriate for BGP local preference egress selection, not the BGP MED conditional comparison defect at Stonebridge ISP. Verify instead: Chosen paths match the configured local-preference intent and MED is considered only where applicable in the selection order.
Question 204
After corrective implementation at fictional Stonebridge ISP, reviewers revisit: An operator expects a lower MED to override a higher local preference when choosing between multiple BGP paths. Which safeguard best protects the repaired state?
Retest this approved Junos service-provider routing and switching control after relevant changes: Chosen paths match the configured local-preference intent and MED is considered only where applicable in the selection order.
Retest this approved Junos service-provider routing and switching control after relevant changes: The intended internal clients learn the prefix through the approved reflection or full-mesh topology.
Retest this approved Junos service-provider routing and switching control after relevant changes: show bgp neighbor returns Established after synchronized authentication and unauthorized attempts still fail.
Retest this approved Junos service-provider routing and switching control after relevant changes: The observed reset reason is documented and a targeted correction yields stable Established state.
Explanation
Correct Answer
A:
This periodic check is appropriate because it examines the exact prior failure at Stonebridge ISP: Chosen paths match the configured local-preference intent and MED is considered only where applicable in the selection order.
Incorrect Answers
B:
This recurring check measures IBGP split horizon route reflector, whereas the fixed BGP MED conditional comparison behavior needs ongoing evidence that: Chosen paths match the configured local-preference intent and MED is considered only where applicable in the selection order.
C:
That control would prevent the different failure Configured peer authentication keys are inconsistent between the two BGP endpoints. It would not detect recurrence of: The decision assumes MED outranks local preference in the BGP selection process, which is not generally correct.
D:
The proposed check belongs to the separate BGP notification diagnostics issue at Cedar Mobile. For this case, retest: Chosen paths match the configured local-preference intent and MED is considered only where applicable in the selection order.
Question 205
For fictional Stonebridge ISP, identify the shortcut that fails to address: An operator expects a lower MED to override a higher local preference when choosing between multiple BGP paths.
Claim AS-path prepending guarantees every Internet network will avoid the backup link.
Remove session authentication everywhere because it prevents the mismatched peer from connecting.
Make every MED zero and disregard upstream policy to force a desired path.
Change remote MED attributes on unrelated inbound routes and assume local preference is unaffected.
Explanation
Correct Answer
C:
The proposed shortcut undermines the expected result: Chosen paths match the configured local-preference intent and MED is considered only where applicable in the selection order. The safer implementation step is: Inspect best-path criteria in order and use approved local preference for intra-AS outbound selection before evaluating MED.
Incorrect Answers
A:
This shortcut would also be unsafe, but for a different BGP AS path prepend inbound influence case (A dual-homed customer wants to reduce inbound use of a backup circuit, but advertises identical AS paths on both upstream links.). It does not repeat the defect in this question: The decision assumes MED outranks local preference in the BGP selection process, which is not generally correct.
B:
The proposal recreates the separate BGP authentication mismatch error. The current case instead concerns: An operator expects a lower MED to override a higher local preference when choosing between multiple BGP paths. Its specific failed assumption is: The decision assumes MED outranks local preference in the BGP selection process, which is not generally correct.
D:
This shortcut would also be unsafe, but for a different BGP local preference egress selection case (Two routes learned from different upstream providers have comparable reachability, but outbound traffic follows the less-preferred contract.). It does not repeat the defect in this question: The decision assumes MED outranks local preference in the BGP selection process, which is not generally correct.
Question 206
At fictional Cobalt Datacenter (data center interconnect), this Junos network defect is reported: A dual-homed customer wants to reduce inbound use of a backup circuit, but advertises identical AS paths on both upstream links. What should the specialist change first?
Restrict export terms to approved customer-visible prefixes and verify the peer-specific advertisement list.
Restore approved IP reachability and TCP port 179 access, then inspect BGP session establishment.
Apply a controlled outbound AS-path prepend on the backup advertisement and confirm peer acceptance, noting other networks retain discretion.
Check the relevant RIB, current peer advertisements and route withdrawal state before deleting configurations.
Explanation
Correct Answer
C:
The symptoms point to this control gap: Without a deliberate upstream-accepted path-policy difference, remote AS path decisions may not prefer the intended primary ingress. The targeted action is Apply a controlled outbound AS-path prepend on the backup advertisement and confirm peer acceptance, noting other networks retain discretion. Verify success by confirming: Remote route views show the deliberate longer AS path on the backup and sampled ingress behavior meets the agreed objective.
Incorrect Answers
A:
The proposal is a correction for BGP outbound prefix leak, not this situation: A dual-homed customer wants to reduce inbound use of a backup circuit, but advertises identical AS paths on both upstream links. Here the cause is: Without a deliberate upstream-accepted path-policy difference, remote AS path decisions may not prefer the intended primary ingress.
B:
Although relevant to BGP TCP reachability, this configuration does not remedy the reported BGP AS path prepend inbound influence failure. Use: Apply a controlled outbound AS-path prepend on the backup advertisement and confirm peer acceptance, noting other networks retain discretion.
D:
The proposal is a correction for BGP withdraw failure interpretation, not this situation: A dual-homed customer wants to reduce inbound use of a backup circuit, but advertises identical AS paths on both upstream links. Here the cause is: Without a deliberate upstream-accepted path-policy difference, remote AS path decisions may not prefer the intended primary ingress.
Question 207
A Junos routing specialist investigates at fictional Cobalt Datacenter: A dual-homed customer wants to reduce inbound use of a backup circuit, but advertises identical AS paths on both upstream links. What control gap requires attention?
Without a deliberate upstream-accepted path-policy difference, remote AS path decisions may not prefer the intended primary ingress.
The decision assumes MED outranks local preference in the BGP selection process, which is not generally correct.
The advertised BGP NEXT_HOP attribute is not recursively resolvable from the internal router.
A stale or alternate-table record is being conflated with active accepted and currently advertised BGP reachability.
Explanation
Correct Answer
A:
Fictional Cobalt Datacenter demonstrates this underlying defect: Without a deliberate upstream-accepted path-policy difference, remote AS path decisions may not prefer the intended primary ingress. Validate after remediation by checking: Remote route views show the deliberate longer AS path on the backup and sampled ingress behavior meets the agreed objective.
Incorrect Answers
B:
That diagnosis belongs to BGP MED conditional comparison, for example: An operator expects a lower MED to override a higher local preference when choosing between multiple BGP paths. It does not explain this case, which is caused by: Without a deliberate upstream-accepted path-policy difference, remote AS path decisions may not prefer the intended primary ingress.
C:
The alternate cause would explain BGP NEXT_HOP reachability. For BGP AS path prepend inbound influence at Cobalt Datacenter, the evidence instead supports: Without a deliberate upstream-accepted path-policy difference, remote AS path decisions may not prefer the intended primary ingress.
D:
This is a different failure mechanism: A stale or alternate-table record is being conflated with active accepted and currently advertised BGP reachability. The current symptom is: A dual-homed customer wants to reduce inbound use of a backup circuit, but advertises identical AS paths on both upstream links. The more direct defect is: Without a deliberate upstream-accepted path-policy difference, remote AS path decisions may not prefer the intended primary ingress.
Question 208
Following remediation at fictional Cobalt Datacenter, how should the team verify that this specific issue is resolved? A dual-homed customer wants to reduce inbound use of a backup circuit, but advertises identical AS paths on both upstream links.
The selected BGP path uses the intended provider across internal routers without affecting received prefix filtering.
Remote route views show the deliberate longer AS path on the backup and sampled ingress behavior meets the agreed objective.
The iBGP route's next hop resolves and the correct prefix is active without leaking an external management network.
show bgp neighbor reports Established with the expected peer AS and authorized prefixes can be exchanged.
Explanation
Correct Answer
B:
This outcome directly measures BGP AS path prepend inbound influence: Remote route views show the deliberate longer AS path on the backup and sampled ingress behavior meets the agreed objective. It tests the diagnosed issue: Without a deliberate upstream-accepted path-policy difference, remote AS path decisions may not prefer the intended primary ingress.
Incorrect Answers
A:
That result would validate the separate BGP local preference egress selection scenario (Two routes learned from different upstream providers have comparable reachability, but outbound traffic follows the less-preferred contract.). It does not prove the needed BGP AS path prepend inbound influence outcome: Remote route views show the deliberate longer AS path on the backup and sampled ingress behavior meets the agreed objective.
C:
The alternative proof tests a different cause: The advertised BGP NEXT_HOP attribute is not recursively resolvable from the internal router. The relevant acceptance condition remains: Remote route views show the deliberate longer AS path on the backup and sampled ingress behavior meets the agreed objective.
D:
That result would validate the separate BGP AS number mismatch scenario (Two eBGP neighbors have IP connectivity but the session never progresses to Established after the remote carrier changes its autonomous system number.). It does not prove the needed BGP AS path prepend inbound influence outcome: Remote route views show the deliberate longer AS path on the backup and sampled ingress behavior meets the agreed objective.
Question 209
After corrective implementation at fictional Cobalt Datacenter, reviewers revisit: A dual-homed customer wants to reduce inbound use of a backup circuit, but advertises identical AS paths on both upstream links. Which safeguard best protects the repaired state?
Retest this approved Junos service-provider routing and switching control after relevant changes: Remote route views show the deliberate longer AS path on the backup and sampled ingress behavior meets the agreed objective.
Retest this approved Junos service-provider routing and switching control after relevant changes: The departed prefix is absent from current external advertisements and the proper active forwarding table.
Retest this approved Junos service-provider routing and switching control after relevant changes: The intended route becomes eligible while a disallowed customer prefix is still filtered.
Retest this approved Junos service-provider routing and switching control after relevant changes: Chosen paths match the configured local-preference intent and MED is considered only where applicable in the selection order.
Explanation
Correct Answer
A:
A recurring safeguard for BGP AS path prepend inbound influence should test this actual outcome: Remote route views show the deliberate longer AS path on the backup and sampled ingress behavior meets the agreed objective. It exercises the configured correction: Apply a controlled outbound AS-path prepend on the backup advertisement and confirm peer acceptance, noting other networks retain discretion.
Incorrect Answers
B:
The proposed check belongs to the separate BGP withdraw failure interpretation issue at Pinecrest Cable. For this case, retest: Remote route views show the deliberate longer AS path on the backup and sampled ingress behavior meets the agreed objective.
C:
This recurring check measures BGP policy import filter, whereas the fixed BGP AS path prepend inbound influence behavior needs ongoing evidence that: Remote route views show the deliberate longer AS path on the backup and sampled ingress behavior meets the agreed objective.
D:
That control would prevent the different failure The decision assumes MED outranks local preference in the BGP selection process, which is not generally correct. It would not detect recurrence of: Without a deliberate upstream-accepted path-policy difference, remote AS path decisions may not prefer the intended primary ingress.
Question 210
For fictional Cobalt Datacenter, identify the shortcut that fails to address: A dual-homed customer wants to reduce inbound use of a backup circuit, but advertises identical AS paths on both upstream links.
Claim AS-path prepending guarantees every Internet network will avoid the backup link.
Change the group policy blindly and assume peer-specific overrides will disappear.
Delete all BGP groups simply because a non-active historical prefix is visible somewhere.
Increase BGP route preference without checking the ASN carried by the remote peer.
Explanation
Correct Answer
A:
The proposed shortcut undermines the expected result: Remote route views show the deliberate longer AS path on the backup and sampled ingress behavior meets the agreed objective. The safer implementation step is: Apply a controlled outbound AS-path prepend on the backup advertisement and confirm peer acceptance, noting other networks retain discretion.
Incorrect Answers
B:
This shortcut would also be unsafe, but for a different BGP peer group inheritance case (One member of a BGP group has a peer-specific outbound policy override and advertises a different set of prefixes than sibling peers.). It does not repeat the defect in this question: Without a deliberate upstream-accepted path-policy difference, remote AS path decisions may not prefer the intended primary ingress.
C:
The proposal recreates the separate BGP withdraw failure interpretation error. The current case instead concerns: A dual-homed customer wants to reduce inbound use of a backup circuit, but advertises identical AS paths on both upstream links. Its specific failed assumption is: Without a deliberate upstream-accepted path-policy difference, remote AS path decisions may not prefer the intended primary ingress.
D:
This alternative is problematic for BGP AS number mismatch, rather than the reported BGP AS path prepend inbound influence. Corrective action here is: Apply a controlled outbound AS-path prepend on the backup advertisement and confirm peer acceptance, noting other networks retain discretion.
Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-364) Practice Tests
Our team works hard to provide students with high exam practice test questions and compelling learning experiences. We're confident of the quality level of the products we offer and provide no hassle satisfaction guarantee.
Why choose Exam-Labs?613,682+Satisfied Customers since 2015
100% Latest Exam Questions
Accurate & Updated Answers
Regular Free Updates
24/7 Customer Support
Instant Download
Exam Info
Juniper JN0-364 Practice Test Questions, Juniper JN0-364 Exam Practice Test Questions
Looking to pass your tests the first time. You can study with Juniper JN0-364 certification practice test questions and answers, study guide, training courses. With Exam-Labs VCE files you can prepare with Juniper JN0-364 Service Provider Routing and Switching, Specialist (JNCIS-SP) exam practice test questions and answers. The most complete solution for passing with Juniper certification JN0-364 exam practice test questions and answers, study guide, training course.
JN0-364 Service Provider Routing and Switching, Specialist
JN0-364 is the current Service Provider Routing and Switching, Specialist exam as of October 2026. HPE Juniper Networking lists 65 multiple-choice questions in 90 minutes, Pearson VUE delivery, JNCIA-Junos as the prerequisite, and Junos OS 25.2 as the software reference. It replaced JN0-363 on February 2, 2026.
The blueprint is broad: protocol-independent routing, OSPF, IS-IS, BGP, Layer 2 bridging and VLANs, spanning-tree variants, MPLS, IPv6, GRE tunnels, and high availability. The common thread is service-provider operations. Candidates must understand not only what each protocol does but how state is configured, verified, and troubleshot across a Junos network.
The current JN0-106 associate exam provides the Junos foundation. If routing tables, policy, interface hierarchy, or operational mode are still slow, strengthen those first. JN0-364 adds enough simultaneous control planes that weak fundamentals become a major study bottleneck.
Protocol-independent routing is the control surface beneath the protocols
The blueprint includes static, aggregate, and generated routes, martian addresses, routing instances, RIB groups, load balancing, and filter-based forwarding. These are not secondary topics. They determine which tables routes enter, which paths become active, and how traffic can be steered independently of the dynamic protocol that learned a prefix.
Build labs where the same destination appears from multiple sources. Change route preference, create an aggregate, move information between routing instances, and apply filter-based forwarding. Before running a show command, predict which route should be active and why. That habit turns the routing table into a reasoned outcome rather than a display to memorize.
The concepts behind static routing make a clean baseline because they isolate local route selection before dynamic signaling complicates the picture.
OSPF and IS-IS should be practiced as living topology databases
For OSPF, JN0-364 expects knowledge of the link-state database, packet types, router IDs, neighbors, DR/BDR roles, area and router types, LSAs, configuration, policy, and troubleshooting. For IS-IS, candidates need PDUs, TLVs, levels, areas, adjacencies, DIS behavior, metrics, policy, and operational verification.
Do not study those items as vocabulary lists. Form a neighbor, inspect the database, change a metric, remove a link, and watch the shortest-path result change. Repeat the topology with the other protocol. This makes the shared link-state model visible while preserving the differences in hierarchy and protocol behavior.
The detailed explanation of OSPF areas and LSAs is useful, but a service-provider candidate should be equally comfortable reading IS-IS adjacency and database state.
BGP should be verified at every stage between peer and forwarding table
JN0-364 covers BGP messages, attributes, route selection, IBGP/EBGP interaction, peers, options, policy, and troubleshooting. A disciplined verification sequence is essential: confirm transport and session state, inspect received routes, apply policy reasoning, verify next-hop resolution, inspect active routes, and check what is advertised onward.
Create at least one lab where the BGP session remains Established while the desired route disappears. Use import policy, an unreachable next hop, or a competing path. The exercise proves why “peer up” and “service working” are different statements. The broader mechanics of BGP path selection become easier to apply when every attribute change produces visible route-state evidence.
Service-provider BGP work is inseparable from policy. Spend time writing and reading policy terms so that you can explain exactly why a route is accepted, rejected, modified, or exported.
Provider switching topics protect the service edge
The Layer 2 domain includes service-provider switching platforms, bridging concepts, frame processing, virtual switches, Q-in-Q provider bridging, VLAN port modes, tagging, IRB, and spanning-tree variants. These topics matter because service-provider networks often carry customer Layer 2 services even when the core itself is highly routed.
Practice Q-in-Q by distinguishing customer tags from the service-provider tag. Then verify how the frame is handled at ingress, across the provider domain, and at egress. This makes the separation between customer segmentation and provider forwarding explicit.
Spanning tree should be understood with security controls such as BPDU, loop, and root protection. Those features encode expectations at the edge and help prevent customer or access faults from destabilizing a larger Layer 2 domain.
MPLS study should begin with packet forwarding before signaling
The current blueprint includes MPLS terminology, label headers, end-to-end forwarding, label information, routing-table relationships, RSVP, LDP, and segment routing with MPLS. Start with the dataplane. Trace how an ingress node pushes a label, how transit nodes swap it, and how the egress processes the final label.
Then attach each signaling method to the label-switched path it creates. LDP distributes labels along routing paths, RSVP can establish traffic-engineered paths, and segment routing expresses path intent through segments. The concepts in MPLS forwarding provide a strong base when paired with Junos route and label-table output.
Do not memorize labels as static numbers. Focus on the control information that creates them and the forwarding behavior they enable. That perspective scales into VPN and traffic-engineering work at the professional level.
When comparing MPLS control methods, keep one question in view: what information tells the router which labeled path to use? LDP generally couples label distribution to IGP reachability, RSVP can signal traffic-engineered LSPs with explicit constraints, and segment routing represents path intent through ordered segments. Practice reading the resulting state rather than memorizing a feature table. If an LSP is down, determine whether the missing evidence is an IGP route, a signaling relationship, a label binding, or the forwarding entry itself.
Troubleshooting should therefore move from dependency to dependent feature. Verify core addressing and IGP reachability first, then protocol sessions, then label or tunnel state, and finally end-to-end service traffic. This sequence is efficient because later layers cannot be healthy when their transport assumptions are false. It also mirrors real service-provider operations, where the fastest resolution often comes from proving the lowest broken dependency before touching policy or service configuration.
IPv6 belongs in the same routing model as IPv4
JN0-364 covers IPv6 static routing and dynamic routing through OSPFv3, IS-IS, and BGP, plus IPv6-over-IPv4 tunneling. Treat IPv6 as a routed protocol with its own addressing and neighbor behavior rather than as a separate specialty. Route selection, policy, protocol adjacency, and troubleshooting discipline still apply.
Build dual-stack labs so you can compare the same topology under both address families. Verify that a protocol session can be healthy for one family while reachability for another is absent. This teaches you to inspect family-specific route state instead of assuming that one working path proves the other.
For transition tunnels, explicitly trace the outer IPv4 path and the inner IPv6 packet. The layered model is the same one used for GRE and prevents confusion about which address family is failing.
GRE tunnels add reachability without removing underlay dependencies
The tunnel objective covers applications, design considerations, GRE configuration, and troubleshooting. A GRE interface can make two remote networks appear directly connected at the logical layer, but the outer endpoints still depend on ordinary routing. If the underlay cannot reach the tunnel destination, the overlay path cannot work.
In the lab, verify outer routes, tunnel source and destination, inner routing, and MTU. Then break each independently. The difference between an underlay failure and an inner-route problem becomes obvious when you compare packet captures and interface state.
Use the conceptual discussion of GRE tunneling to broaden understanding, while keeping configuration practice aligned to the exact JN0-364 objectives.
High availability combines fast detection with preserved forwarding
Current HA topics include LAG, graceful restart, GRES, NSB, NSR, BFD, and VRRP. Each protects a different part of service continuity. Link aggregation addresses physical path loss, BFD accelerates failure detection, graceful and nonstop mechanisms reduce control-plane disruption, and VRRP protects the first-hop gateway identity.
Build a table that states for each feature what fails, what detects the failure, what state is preserved, and what alternate path or node takes over. The principles of VRRP redundancy are especially useful when contrasted with BFD: one provides a virtual gateway role, the other supplies rapid liveness information.
In testing, record packets lost and convergence time. A protocol can be “working as designed” while still failing a service-level objective if recovery is too slow for the application.
Study the current exam as one service-provider system
Separate notebooks for OSPF, BGP, MPLS, and HA are useful early, but final preparation should combine them. Build a topology where an IGP supplies core reachability, MPLS uses that underlay, BGP carries service or external routes, and HA mechanisms protect critical paths. Then introduce a fault and decide which control plane should react.
Use the objective list as a four-part readiness matrix: explain, configure, verify, troubleshoot. If you can define a feature but cannot identify healthy operational output, the topic is incomplete. If you can configure it but cannot predict the effect of a failure, it is not yet specialist-level knowledge.
The current professional progression represented in the approved inventory is JN0-664. That path rewards candidates who build durable service-provider reasoning now, because advanced Layer 2 VPN, EVPN, MPLS, and policy work assumes the specialist foundation is already fluent.
Before scheduling, verify the live JN0-364 blueprint and software reference again. The certification program's branding changed under HPE Networking in September 2026, but the exam remains centered on Junos service-provider routing and switching. Use current first-party objectives for scope and let hands-on operational evidence—routes, adjacencies, labels, policy results, tunnel state, and failover behavior—drive the final review.
Use Juniper JN0-364 certification exam practice test questions, study guide and training course - the complete package at discounted price. Pass with JN0-364 Service Provider Routing and Switching, Specialist (JNCIS-SP) practice test questions and answers, study guide, complete training course especially formatted in VCE files. Latest Juniper certification JN0-364 exam practice test questions and answers will guarantee your success without studying for endless hours.
FAQs
Juniper JN0-364 Exam Practice Test Questions, Juniper JN0-364 Practice Test Questions and Answers
Do you have questions about our JN0-364 Service Provider Routing and Switching, Specialist (JNCIS-SP) practice test questions and answers or any of our products? If you are not clear about our Juniper JN0-364 exam practice test questions, you can read the FAQ below.
The JN0-364 Premium File has been developed by industry professionals, who have been working with IT certifications for years and have close ties with IT certification vendors and holders - with most recent exam questions and valid answers.
JN0-364 Premium File is presented in VCE format. VCE (Virtual CertExam) is a file format that realistically simulates JN0-364 exam environment, allowing for the most convenient exam preparation you can get - in the convenience of your own home or on the go. If you have ever seen IT exam simulations, chances are, they were in the VCE format.
What is VCE?
VCE is a file format associated with Visual CertExam Software. This format and software are widely used for creating tests for IT certifications. To create and open VCE files, you will need to purchase, download and install VCE Exam Simulator on your computer.
Can I try it for free?
Yes, you can. Look through free VCE files section and download any file you choose absolutely free.
Where do I get VCE Exam Simulator?
VCE Exam Simulator can be purchased from its developer, https://www.avanset.com. Please note that Exam-Labs does not sell or support this software. Should you have any questions or concerns about using this product, please contact Avanset support team directly.
How are Premium VCE files different from Free VCE files?
Premium VCE files have been developed by industry professionals, who have been working with IT certifications for years and have close ties with IT certification vendors and holders - with most recent exam questions and some insider information.
Free VCE files All files are sent by Exam-labs community members. We encourage everyone who has recently taken an exam and/or has come across some braindumps that have turned out to be true to share this information with the community by creating and sending VCE files. We don't say that these free VCEs sent by our members aren't reliable (experience shows that they are). But you should use your critical thinking as to what you download and memorize.
How long will I receive updates for JN0-364 Premium VCE File that I purchased?
Free updates are available during 30 days after you purchased Premium VCE file. After 30 days the file will become unavailable.
How can I get the products after purchase?
All products are available for download immediately from your Member's Area. Once you have made the payment, you will be transferred to Member's Area where you can login and download the products you have purchased to your PC or another device.
Will I be able to renew my products when they expire?
Yes, when the 30 days of your product validity are over, you have the option of renewing your expired products with a 30% discount. This can be done in your Member's Area.
Please note that you will not be able to use the product after it has expired if you don't renew it.
How often are the questions updated?
We always try to provide the latest pool of questions, Updates in the questions depend on the changes in actual pool of questions by different vendors. As soon as we know about the change in the exam question pool we try our best to update the products as fast as possible.
What is a Study Guide?
Study Guides available on Exam-Labs are built by industry professionals who have been working with IT certifications for years. Study Guides offer full coverage on exam objectives in a systematic approach. Study Guides are very useful for fresh applicants and provides background knowledge about preparation of exams.
How can I open a Study Guide?
Any study guide can be opened by an official Acrobat by Adobe or any other reader application you use.
What is a Training Course?
Training Courses we offer on Exam-Labs in video format are created and managed by IT professionals. The foundation of each course are its lectures, which can include videos, slides and text. In addition, authors can add resources and various types of practice activities, as a way to enhance the learning experience of students.
Enter Your Email Address to Proceed
Please fill out your email address below in order to purchase Certification/Exam.
Enter Your Email Address to Proceed
Please fill out your email address below in order to purchase Demo.
How It Works
Step 1. Choose Exam on Exam-Labs
Download IT Exams Questions & Answers
Step 2. Open Exam with Avanset Exam Simulator
Press here to download VCE Exam Simulator that simulates latest exam environment