Includes questions types found on actual exam such as drag and drop, simulation, type in, and fill in the blank.
Service Provider Routing and Switching, Specialist (JNCIS-SP) JN0-364 Practice Test 43
Question 420
For fictional Alder Telecom, identify the shortcut that fails to address: An established IPv4 BGP session is expected to transport IPv6 reachability but has no applicable IPv6 unicast family or address-policy configuration.
Assume an IPv4 BGP Established state automatically advertises every IPv6 route.
Add IPv6 routes pointing to unreachable tunnel endpoints and ignore IPv4 encapsulation reachability.
Copy the same link-local address into every interface route without preserving its interface scope.
Modify IPv4 OSPF area costs while never activating OSPFv3 for IPv6 forwarding.
Explanation
Correct Answer
A:
The proposed shortcut undermines the expected result: The peer exchanges only authorized IPv6 prefixes while existing IPv4 BGP behavior is preserved. The safer implementation step is: Configure the approved BGP IPv6 unicast family and prefix policy on each side and inspect IPv6 routes.
Incorrect Answers
B:
This shortcut would also be unsafe, but for a different IPv6 over IPv4 tunnel case (Two IPv6 access islands use an IPv4 provider core but the configured encapsulation endpoints cannot reach one another over IPv4.). It does not repeat the defect in this question: The established BGP transport session does not imply correct IPv6 address-family advertisement and reception.
C:
The proposal recreates the separate IPv6 static route link local gateway error. The current case instead concerns: An established IPv4 BGP session is expected to transport IPv6 reachability but has no applicable IPv6 unicast family or address-policy configuration. Its specific failed assumption is: The established BGP transport session does not imply correct IPv6 address-family advertisement and reception.
D:
This alternative is problematic for OSPFv3 neighbor state, rather than the reported MP BGP IPv6 route family. Corrective action here is: Configure the approved BGP IPv6 unicast family and prefix policy on each side and inspect IPv6 routes.
Question 421
At fictional Harbor Core (core network), this Junos network defect is reported: A dual-stack backbone has operational IS-IS adjacencies but the IPv6 loopbacks are missing in the protocol's IPv6 reachability advertisements. What should the specialist change first?
Enable the appropriate OSPFv3 interface and area configuration and verify its neighbor state.
Check the IS-IS IPv6 address-family setup, applicable interface reachability and exported IPv6 prefixes.
Configure the approved BGP IPv6 unicast family and prefix policy on each side and inspect IPv6 routes.
Specify the supported link-local next-hop with the associated egress interface and verify route installation.
Explanation
Correct Answer
B:
This response addresses the specific IS-IS IPv6 reachability failure at Harbor Core. Apply: Check the IS-IS IPv6 address-family setup, applicable interface reachability and exported IPv6 prefixes. Its acceptance test is: IPv6 loopbacks appear as intended in IS-IS-learned routes and can be reached over the backbone.
Incorrect Answers
A:
That action would address the separate OSPFv3 neighbor state case, where A new IPv6-only transit link pings successfully but OSPFv3 routes are absent because the engineer enabled OSPFv2 instead. The present IS-IS IPv6 reachability issue instead requires: Check the IS-IS IPv6 address-family setup, applicable interface reachability and exported IPv6 prefixes.
C:
Although relevant to MP BGP IPv6 route family, this configuration does not remedy the reported IS-IS IPv6 reachability failure. Use: Check the IS-IS IPv6 address-family setup, applicable interface reachability and exported IPv6 prefixes.
D:
That action would address the separate IPv6 static route link local gateway case, where A provider edge installs an IPv6 static default using only a next-hop link-local address and fails to bind the intended outgoing interface. The present IS-IS IPv6 reachability issue instead requires: Check the IS-IS IPv6 address-family setup, applicable interface reachability and exported IPv6 prefixes.
Question 422
A Junos routing specialist investigates at fictional Harbor Core: A dual-stack backbone has operational IS-IS adjacencies but the IPv6 loopbacks are missing in the protocol's IPv6 reachability advertisements. What control gap requires attention?
IS-IS adjacency existence alone does not prove IPv6 protocol reachability has been configured and advertised.
IPv6 link-local next hops are interface scoped and require the correct egress interface context.
The established BGP transport session does not imply correct IPv6 address-family advertisement and reception.
The intended IPv6 routing process OSPFv3 is not configured on the transit interface.
Explanation
Correct Answer
A:
The most direct cause for IS-IS IPv6 reachability is IS-IS adjacency existence alone does not prove IPv6 protocol reachability has been configured and advertised. The appropriate response is Check the IS-IS IPv6 address-family setup, applicable interface reachability and exported IPv6 prefixes.
Incorrect Answers
B:
This is a different failure mechanism: IPv6 link-local next hops are interface scoped and require the correct egress interface context. The current symptom is: A dual-stack backbone has operational IS-IS adjacencies but the IPv6 loopbacks are missing in the protocol's IPv6 reachability advertisements. The more direct defect is: IS-IS adjacency existence alone does not prove IPv6 protocol reachability has been configured and advertised.
C:
That diagnosis belongs to MP BGP IPv6 route family, for example: An established IPv4 BGP session is expected to transport IPv6 reachability but has no applicable IPv6 unicast family or address-policy configuration. It does not explain this case, which is caused by: IS-IS adjacency existence alone does not prove IPv6 protocol reachability has been configured and advertised.
D:
The alternate cause would explain OSPFv3 neighbor state. For IS-IS IPv6 reachability at Harbor Core, the evidence instead supports: IS-IS adjacency existence alone does not prove IPv6 protocol reachability has been configured and advertised.
Question 423
Following remediation at fictional Harbor Core, how should the team verify that this specific issue is resolved? A dual-stack backbone has operational IS-IS adjacencies but the IPv6 loopbacks are missing in the protocol's IPv6 reachability advertisements.
IPv6 loopbacks appear as intended in IS-IS-learned routes and can be reached over the backbone.
The IPv6 route resolves through the intended interface and the next-hop neighbor is reachable.
The peer exchanges only authorized IPv6 prefixes while existing IPv4 BGP behavior is preserved.
show ospf3 neighbor reports the expected peer and IPv6 prefixes are learned through OSPFv3.
Explanation
Correct Answer
A:
Sign-off requires case-specific evidence: IPv6 loopbacks appear as intended in IS-IS-learned routes and can be reached over the backbone. Without that observation, is-is adjacency existence alone does not prove ipv6 protocol reachability has been configured and advertised.
Incorrect Answers
B:
That result would validate the separate IPv6 static route link local gateway scenario (A provider edge installs an IPv6 static default using only a next-hop link-local address and fails to bind the intended outgoing interface.). It does not prove the needed IS-IS IPv6 reachability outcome: IPv6 loopbacks appear as intended in IS-IS-learned routes and can be reached over the backbone.
C:
This observation is appropriate for MP BGP IPv6 route family, not the IS-IS IPv6 reachability defect at Harbor Core. Verify instead: IPv6 loopbacks appear as intended in IS-IS-learned routes and can be reached over the backbone.
D:
The alternative proof tests a different cause: The intended IPv6 routing process OSPFv3 is not configured on the transit interface. The relevant acceptance condition remains: IPv6 loopbacks appear as intended in IS-IS-learned routes and can be reached over the backbone.
Question 424
After corrective implementation at fictional Harbor Core, reviewers revisit: A dual-stack backbone has operational IS-IS adjacencies but the IPv6 loopbacks are missing in the protocol's IPv6 reachability advertisements. Which safeguard best protects the repaired state?
Retest this approved Junos service-provider routing and switching control after relevant changes: show ospf3 neighbor reports the expected peer and IPv6 prefixes are learned through OSPFv3.
Retest this approved Junos service-provider routing and switching control after relevant changes: The peer exchanges only authorized IPv6 prefixes while existing IPv4 BGP behavior is preserved.
Retest this approved Junos service-provider routing and switching control after relevant changes: IPv6 loopbacks appear as intended in IS-IS-learned routes and can be reached over the backbone.
Retest this approved Junos service-provider routing and switching control after relevant changes: The IPv6 route resolves through the intended interface and the next-hop neighbor is reachable.
Explanation
Correct Answer
C:
This periodic check is appropriate because it examines the exact prior failure at Harbor Core: IPv6 loopbacks appear as intended in IS-IS-learned routes and can be reached over the backbone.
Incorrect Answers
A:
This recurring check measures OSPFv3 neighbor state, whereas the fixed IS-IS IPv6 reachability behavior needs ongoing evidence that: IPv6 loopbacks appear as intended in IS-IS-learned routes and can be reached over the backbone.
B:
That control would prevent the different failure The established BGP transport session does not imply correct IPv6 address-family advertisement and reception. It would not detect recurrence of: IS-IS adjacency existence alone does not prove IPv6 protocol reachability has been configured and advertised.
D:
This recurring check measures IPv6 static route link local gateway, whereas the fixed IS-IS IPv6 reachability behavior needs ongoing evidence that: IPv6 loopbacks appear as intended in IS-IS-learned routes and can be reached over the backbone.
Question 425
For fictional Harbor Core, identify the shortcut that fails to address: A dual-stack backbone has operational IS-IS adjacencies but the IPv6 loopbacks are missing in the protocol's IPv6 reachability advertisements.
Assume an IPv4 BGP Established state automatically advertises every IPv6 route.
Modify IPv4 OSPF area costs while never activating OSPFv3 for IPv6 forwarding.
Re-create the already-Up IS-IS neighbors without checking IPv6 reachability configuration.
Copy the same link-local address into every interface route without preserving its interface scope.
Explanation
Correct Answer
C:
That shortcut preserves the original IS-IS IPv6 reachability weakness: IS-IS adjacency existence alone does not prove IPv6 protocol reachability has been configured and advertised. The controlled alternative is: Check the IS-IS IPv6 address-family setup, applicable interface reachability and exported IPv6 prefixes.
Incorrect Answers
A:
The proposal recreates the separate MP BGP IPv6 route family error. The current case instead concerns: A dual-stack backbone has operational IS-IS adjacencies but the IPv6 loopbacks are missing in the protocol's IPv6 reachability advertisements. Its specific failed assumption is: IS-IS adjacency existence alone does not prove IPv6 protocol reachability has been configured and advertised.
B:
This alternative is problematic for OSPFv3 neighbor state, rather than the reported IS-IS IPv6 reachability. Corrective action here is: Check the IS-IS IPv6 address-family setup, applicable interface reachability and exported IPv6 prefixes.
D:
The proposal recreates the separate IPv6 static route link local gateway error. The current case instead concerns: A dual-stack backbone has operational IS-IS adjacencies but the IPv6 loopbacks are missing in the protocol's IPv6 reachability advertisements. Its specific failed assumption is: IS-IS adjacency existence alone does not prove IPv6 protocol reachability has been configured and advertised.
Question 426
At fictional Morrow Networks (wholesale access), this Junos network defect is reported: Two IPv6 access islands use an IPv4 provider core but the configured encapsulation endpoints cannot reach one another over IPv4. What should the specialist change first?
Check the IS-IS IPv6 address-family setup, applicable interface reachability and exported IPv6 prefixes.
Enable the appropriate OSPFv3 interface and area configuration and verify its neighbor state.
Validate IPv4 underlay endpoint reachability and tunnel interface parameters before configuring IPv6 reachability over the tunnel.
Configure the approved BGP IPv6 unicast family and prefix policy on each side and inspect IPv6 routes.
Explanation
Correct Answer
C:
This response addresses the specific IPv6 over IPv4 tunnel failure at Morrow Networks. Apply: Validate IPv4 underlay endpoint reachability and tunnel interface parameters before configuring IPv6 reachability over the tunnel. Its acceptance test is: IPv6 test packets traverse the intended IPv4 tunnel and the decapsulated destination receives them.
Incorrect Answers
A:
Although relevant to IS-IS IPv6 reachability, this configuration does not remedy the reported IPv6 over IPv4 tunnel failure. Use: Validate IPv4 underlay endpoint reachability and tunnel interface parameters before configuring IPv6 reachability over the tunnel.
B:
That action would address the separate OSPFv3 neighbor state case, where A new IPv6-only transit link pings successfully but OSPFv3 routes are absent because the engineer enabled OSPFv2 instead. The present IPv6 over IPv4 tunnel issue instead requires: Validate IPv4 underlay endpoint reachability and tunnel interface parameters before configuring IPv6 reachability over the tunnel.
D:
Although relevant to MP BGP IPv6 route family, this configuration does not remedy the reported IPv6 over IPv4 tunnel failure. Use: Validate IPv4 underlay endpoint reachability and tunnel interface parameters before configuring IPv6 reachability over the tunnel.
Question 427
A Junos routing specialist investigates at fictional Morrow Networks: Two IPv6 access islands use an IPv4 provider core but the configured encapsulation endpoints cannot reach one another over IPv4. What control gap requires attention?
The intended IPv6 routing process OSPFv3 is not configured on the transit interface.
The established BGP transport session does not imply correct IPv6 address-family advertisement and reception.
IS-IS adjacency existence alone does not prove IPv6 protocol reachability has been configured and advertised.
IPv6-over-IPv4 transport requires working IPv4 endpoint reachability and matching tunnel setup.
Explanation
Correct Answer
D:
The scenario is explained by: IPv6-over-IPv4 transport requires working IPv4 endpoint reachability and matching tunnel setup. This is distinct from unrelated application failures. The recommended correction is: Validate IPv4 underlay endpoint reachability and tunnel interface parameters before configuring IPv6 reachability over the tunnel.
Incorrect Answers
A:
That diagnosis belongs to OSPFv3 neighbor state, for example: A new IPv6-only transit link pings successfully but OSPFv3 routes are absent because the engineer enabled OSPFv2 instead. It does not explain this case, which is caused by: IPv6-over-IPv4 transport requires working IPv4 endpoint reachability and matching tunnel setup.
B:
The alternate cause would explain MP BGP IPv6 route family. For IPv6 over IPv4 tunnel at Morrow Networks, the evidence instead supports: IPv6-over-IPv4 transport requires working IPv4 endpoint reachability and matching tunnel setup.
C:
This is a different failure mechanism: IS-IS adjacency existence alone does not prove IPv6 protocol reachability has been configured and advertised. The current symptom is: Two IPv6 access islands use an IPv4 provider core but the configured encapsulation endpoints cannot reach one another over IPv4. The more direct defect is: IPv6-over-IPv4 transport requires working IPv4 endpoint reachability and matching tunnel setup.
Question 428
Following remediation at fictional Morrow Networks, how should the team verify that this specific issue is resolved? Two IPv6 access islands use an IPv4 provider core but the configured encapsulation endpoints cannot reach one another over IPv4.
IPv6 test packets traverse the intended IPv4 tunnel and the decapsulated destination receives them.
show ospf3 neighbor reports the expected peer and IPv6 prefixes are learned through OSPFv3.
IPv6 loopbacks appear as intended in IS-IS-learned routes and can be reached over the backbone.
The peer exchanges only authorized IPv6 prefixes while existing IPv4 BGP behavior is preserved.
Explanation
Correct Answer
A:
This outcome directly measures IPv6 over IPv4 tunnel: IPv6 test packets traverse the intended IPv4 tunnel and the decapsulated destination receives them. It tests the diagnosed issue: IPv6-over-IPv4 transport requires working IPv4 endpoint reachability and matching tunnel setup.
Incorrect Answers
B:
The alternative proof tests a different cause: The intended IPv6 routing process OSPFv3 is not configured on the transit interface. The relevant acceptance condition remains: IPv6 test packets traverse the intended IPv4 tunnel and the decapsulated destination receives them.
C:
That result would validate the separate IS-IS IPv6 reachability scenario (A dual-stack backbone has operational IS-IS adjacencies but the IPv6 loopbacks are missing in the protocol's IPv6 reachability advertisements.). It does not prove the needed IPv6 over IPv4 tunnel outcome: IPv6 test packets traverse the intended IPv4 tunnel and the decapsulated destination receives them.
D:
This observation is appropriate for MP BGP IPv6 route family, not the IPv6 over IPv4 tunnel defect at Morrow Networks. Verify instead: IPv6 test packets traverse the intended IPv4 tunnel and the decapsulated destination receives them.
Question 429
After corrective implementation at fictional Morrow Networks, reviewers revisit: Two IPv6 access islands use an IPv4 provider core but the configured encapsulation endpoints cannot reach one another over IPv4. Which safeguard best protects the repaired state?
Retest this approved Junos service-provider routing and switching control after relevant changes: IPv6 test packets traverse the intended IPv4 tunnel and the decapsulated destination receives them.
Retest this approved Junos service-provider routing and switching control after relevant changes: The peer exchanges only authorized IPv6 prefixes while existing IPv4 BGP behavior is preserved.
Retest this approved Junos service-provider routing and switching control after relevant changes: IPv6 loopbacks appear as intended in IS-IS-learned routes and can be reached over the backbone.
Retest this approved Junos service-provider routing and switching control after relevant changes: show ospf3 neighbor reports the expected peer and IPv6 prefixes are learned through OSPFv3.
Explanation
Correct Answer
A:
This periodic check is appropriate because it examines the exact prior failure at Morrow Networks: IPv6 test packets traverse the intended IPv4 tunnel and the decapsulated destination receives them.
Incorrect Answers
B:
This recurring check measures MP BGP IPv6 route family, whereas the fixed IPv6 over IPv4 tunnel behavior needs ongoing evidence that: IPv6 test packets traverse the intended IPv4 tunnel and the decapsulated destination receives them.
C:
That control would prevent the different failure IS-IS adjacency existence alone does not prove IPv6 protocol reachability has been configured and advertised. It would not detect recurrence of: IPv6-over-IPv4 transport requires working IPv4 endpoint reachability and matching tunnel setup.
D:
The proposed check belongs to the separate OSPFv3 neighbor state issue at Meridian Fiber. For this case, retest: IPv6 test packets traverse the intended IPv4 tunnel and the decapsulated destination receives them.
Question 430
For fictional Morrow Networks, identify the shortcut that fails to address: Two IPv6 access islands use an IPv4 provider core but the configured encapsulation endpoints cannot reach one another over IPv4.
Add IPv6 routes pointing to unreachable tunnel endpoints and ignore IPv4 encapsulation reachability.
Re-create the already-Up IS-IS neighbors without checking IPv6 reachability configuration.
Modify IPv4 OSPF area costs while never activating OSPFv3 for IPv6 forwarding.
Assume an IPv4 BGP Established state automatically advertises every IPv6 route.
Explanation
Correct Answer
A:
That shortcut preserves the original IPv6 over IPv4 tunnel weakness: IPv6-over-IPv4 transport requires working IPv4 endpoint reachability and matching tunnel setup. The controlled alternative is: Validate IPv4 underlay endpoint reachability and tunnel interface parameters before configuring IPv6 reachability over the tunnel.
Incorrect Answers
B:
The proposal recreates the separate IS-IS IPv6 reachability error. The current case instead concerns: Two IPv6 access islands use an IPv4 provider core but the configured encapsulation endpoints cannot reach one another over IPv4. Its specific failed assumption is: IPv6-over-IPv4 transport requires working IPv4 endpoint reachability and matching tunnel setup.
C:
This alternative is problematic for OSPFv3 neighbor state, rather than the reported IPv6 over IPv4 tunnel. Corrective action here is: Validate IPv4 underlay endpoint reachability and tunnel interface parameters before configuring IPv6 reachability over the tunnel.
D:
This shortcut would also be unsafe, but for a different MP BGP IPv6 route family case (An established IPv4 BGP session is expected to transport IPv6 reachability but has no applicable IPv6 unicast family or address-policy configuration.). It does not repeat the defect in this question: IPv6-over-IPv4 transport requires working IPv4 endpoint reachability and matching tunnel setup.
Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-364) Practice Tests
Our team works hard to provide students with high exam practice test questions and compelling learning experiences. We're confident of the quality level of the products we offer and provide no hassle satisfaction guarantee.
Why choose Exam-Labs?613,682+Satisfied Customers since 2015
100% Latest Exam Questions
Accurate & Updated Answers
Regular Free Updates
24/7 Customer Support
Instant Download
Exam Info
Juniper JN0-364 Practice Test Questions, Juniper JN0-364 Exam Practice Test Questions
Looking to pass your tests the first time. You can study with Juniper JN0-364 certification practice test questions and answers, study guide, training courses. With Exam-Labs VCE files you can prepare with Juniper JN0-364 Service Provider Routing and Switching, Specialist (JNCIS-SP) exam practice test questions and answers. The most complete solution for passing with Juniper certification JN0-364 exam practice test questions and answers, study guide, training course.
JN0-364 Service Provider Routing and Switching, Specialist
JN0-364 is the current Service Provider Routing and Switching, Specialist exam as of October 2026. HPE Juniper Networking lists 65 multiple-choice questions in 90 minutes, Pearson VUE delivery, JNCIA-Junos as the prerequisite, and Junos OS 25.2 as the software reference. It replaced JN0-363 on February 2, 2026.
The blueprint is broad: protocol-independent routing, OSPF, IS-IS, BGP, Layer 2 bridging and VLANs, spanning-tree variants, MPLS, IPv6, GRE tunnels, and high availability. The common thread is service-provider operations. Candidates must understand not only what each protocol does but how state is configured, verified, and troubleshot across a Junos network.
The current JN0-106 associate exam provides the Junos foundation. If routing tables, policy, interface hierarchy, or operational mode are still slow, strengthen those first. JN0-364 adds enough simultaneous control planes that weak fundamentals become a major study bottleneck.
Protocol-independent routing is the control surface beneath the protocols
The blueprint includes static, aggregate, and generated routes, martian addresses, routing instances, RIB groups, load balancing, and filter-based forwarding. These are not secondary topics. They determine which tables routes enter, which paths become active, and how traffic can be steered independently of the dynamic protocol that learned a prefix.
Build labs where the same destination appears from multiple sources. Change route preference, create an aggregate, move information between routing instances, and apply filter-based forwarding. Before running a show command, predict which route should be active and why. That habit turns the routing table into a reasoned outcome rather than a display to memorize.
The concepts behind static routing make a clean baseline because they isolate local route selection before dynamic signaling complicates the picture.
OSPF and IS-IS should be practiced as living topology databases
For OSPF, JN0-364 expects knowledge of the link-state database, packet types, router IDs, neighbors, DR/BDR roles, area and router types, LSAs, configuration, policy, and troubleshooting. For IS-IS, candidates need PDUs, TLVs, levels, areas, adjacencies, DIS behavior, metrics, policy, and operational verification.
Do not study those items as vocabulary lists. Form a neighbor, inspect the database, change a metric, remove a link, and watch the shortest-path result change. Repeat the topology with the other protocol. This makes the shared link-state model visible while preserving the differences in hierarchy and protocol behavior.
The detailed explanation of OSPF areas and LSAs is useful, but a service-provider candidate should be equally comfortable reading IS-IS adjacency and database state.
BGP should be verified at every stage between peer and forwarding table
JN0-364 covers BGP messages, attributes, route selection, IBGP/EBGP interaction, peers, options, policy, and troubleshooting. A disciplined verification sequence is essential: confirm transport and session state, inspect received routes, apply policy reasoning, verify next-hop resolution, inspect active routes, and check what is advertised onward.
Create at least one lab where the BGP session remains Established while the desired route disappears. Use import policy, an unreachable next hop, or a competing path. The exercise proves why “peer up” and “service working” are different statements. The broader mechanics of BGP path selection become easier to apply when every attribute change produces visible route-state evidence.
Service-provider BGP work is inseparable from policy. Spend time writing and reading policy terms so that you can explain exactly why a route is accepted, rejected, modified, or exported.
Provider switching topics protect the service edge
The Layer 2 domain includes service-provider switching platforms, bridging concepts, frame processing, virtual switches, Q-in-Q provider bridging, VLAN port modes, tagging, IRB, and spanning-tree variants. These topics matter because service-provider networks often carry customer Layer 2 services even when the core itself is highly routed.
Practice Q-in-Q by distinguishing customer tags from the service-provider tag. Then verify how the frame is handled at ingress, across the provider domain, and at egress. This makes the separation between customer segmentation and provider forwarding explicit.
Spanning tree should be understood with security controls such as BPDU, loop, and root protection. Those features encode expectations at the edge and help prevent customer or access faults from destabilizing a larger Layer 2 domain.
MPLS study should begin with packet forwarding before signaling
The current blueprint includes MPLS terminology, label headers, end-to-end forwarding, label information, routing-table relationships, RSVP, LDP, and segment routing with MPLS. Start with the dataplane. Trace how an ingress node pushes a label, how transit nodes swap it, and how the egress processes the final label.
Then attach each signaling method to the label-switched path it creates. LDP distributes labels along routing paths, RSVP can establish traffic-engineered paths, and segment routing expresses path intent through segments. The concepts in MPLS forwarding provide a strong base when paired with Junos route and label-table output.
Do not memorize labels as static numbers. Focus on the control information that creates them and the forwarding behavior they enable. That perspective scales into VPN and traffic-engineering work at the professional level.
When comparing MPLS control methods, keep one question in view: what information tells the router which labeled path to use? LDP generally couples label distribution to IGP reachability, RSVP can signal traffic-engineered LSPs with explicit constraints, and segment routing represents path intent through ordered segments. Practice reading the resulting state rather than memorizing a feature table. If an LSP is down, determine whether the missing evidence is an IGP route, a signaling relationship, a label binding, or the forwarding entry itself.
Troubleshooting should therefore move from dependency to dependent feature. Verify core addressing and IGP reachability first, then protocol sessions, then label or tunnel state, and finally end-to-end service traffic. This sequence is efficient because later layers cannot be healthy when their transport assumptions are false. It also mirrors real service-provider operations, where the fastest resolution often comes from proving the lowest broken dependency before touching policy or service configuration.
IPv6 belongs in the same routing model as IPv4
JN0-364 covers IPv6 static routing and dynamic routing through OSPFv3, IS-IS, and BGP, plus IPv6-over-IPv4 tunneling. Treat IPv6 as a routed protocol with its own addressing and neighbor behavior rather than as a separate specialty. Route selection, policy, protocol adjacency, and troubleshooting discipline still apply.
Build dual-stack labs so you can compare the same topology under both address families. Verify that a protocol session can be healthy for one family while reachability for another is absent. This teaches you to inspect family-specific route state instead of assuming that one working path proves the other.
For transition tunnels, explicitly trace the outer IPv4 path and the inner IPv6 packet. The layered model is the same one used for GRE and prevents confusion about which address family is failing.
GRE tunnels add reachability without removing underlay dependencies
The tunnel objective covers applications, design considerations, GRE configuration, and troubleshooting. A GRE interface can make two remote networks appear directly connected at the logical layer, but the outer endpoints still depend on ordinary routing. If the underlay cannot reach the tunnel destination, the overlay path cannot work.
In the lab, verify outer routes, tunnel source and destination, inner routing, and MTU. Then break each independently. The difference between an underlay failure and an inner-route problem becomes obvious when you compare packet captures and interface state.
Use the conceptual discussion of GRE tunneling to broaden understanding, while keeping configuration practice aligned to the exact JN0-364 objectives.
High availability combines fast detection with preserved forwarding
Current HA topics include LAG, graceful restart, GRES, NSB, NSR, BFD, and VRRP. Each protects a different part of service continuity. Link aggregation addresses physical path loss, BFD accelerates failure detection, graceful and nonstop mechanisms reduce control-plane disruption, and VRRP protects the first-hop gateway identity.
Build a table that states for each feature what fails, what detects the failure, what state is preserved, and what alternate path or node takes over. The principles of VRRP redundancy are especially useful when contrasted with BFD: one provides a virtual gateway role, the other supplies rapid liveness information.
In testing, record packets lost and convergence time. A protocol can be “working as designed” while still failing a service-level objective if recovery is too slow for the application.
Study the current exam as one service-provider system
Separate notebooks for OSPF, BGP, MPLS, and HA are useful early, but final preparation should combine them. Build a topology where an IGP supplies core reachability, MPLS uses that underlay, BGP carries service or external routes, and HA mechanisms protect critical paths. Then introduce a fault and decide which control plane should react.
Use the objective list as a four-part readiness matrix: explain, configure, verify, troubleshoot. If you can define a feature but cannot identify healthy operational output, the topic is incomplete. If you can configure it but cannot predict the effect of a failure, it is not yet specialist-level knowledge.
The current professional progression represented in the approved inventory is JN0-664. That path rewards candidates who build durable service-provider reasoning now, because advanced Layer 2 VPN, EVPN, MPLS, and policy work assumes the specialist foundation is already fluent.
Before scheduling, verify the live JN0-364 blueprint and software reference again. The certification program's branding changed under HPE Networking in September 2026, but the exam remains centered on Junos service-provider routing and switching. Use current first-party objectives for scope and let hands-on operational evidence—routes, adjacencies, labels, policy results, tunnel state, and failover behavior—drive the final review.
Use Juniper JN0-364 certification exam practice test questions, study guide and training course - the complete package at discounted price. Pass with JN0-364 Service Provider Routing and Switching, Specialist (JNCIS-SP) practice test questions and answers, study guide, complete training course especially formatted in VCE files. Latest Juniper certification JN0-364 exam practice test questions and answers will guarantee your success without studying for endless hours.
FAQs
Juniper JN0-364 Exam Practice Test Questions, Juniper JN0-364 Practice Test Questions and Answers
Do you have questions about our JN0-364 Service Provider Routing and Switching, Specialist (JNCIS-SP) practice test questions and answers or any of our products? If you are not clear about our Juniper JN0-364 exam practice test questions, you can read the FAQ below.
The JN0-364 Premium File has been developed by industry professionals, who have been working with IT certifications for years and have close ties with IT certification vendors and holders - with most recent exam questions and valid answers.
JN0-364 Premium File is presented in VCE format. VCE (Virtual CertExam) is a file format that realistically simulates JN0-364 exam environment, allowing for the most convenient exam preparation you can get - in the convenience of your own home or on the go. If you have ever seen IT exam simulations, chances are, they were in the VCE format.
What is VCE?
VCE is a file format associated with Visual CertExam Software. This format and software are widely used for creating tests for IT certifications. To create and open VCE files, you will need to purchase, download and install VCE Exam Simulator on your computer.
Can I try it for free?
Yes, you can. Look through free VCE files section and download any file you choose absolutely free.
Where do I get VCE Exam Simulator?
VCE Exam Simulator can be purchased from its developer, https://www.avanset.com. Please note that Exam-Labs does not sell or support this software. Should you have any questions or concerns about using this product, please contact Avanset support team directly.
How are Premium VCE files different from Free VCE files?
Premium VCE files have been developed by industry professionals, who have been working with IT certifications for years and have close ties with IT certification vendors and holders - with most recent exam questions and some insider information.
Free VCE files All files are sent by Exam-labs community members. We encourage everyone who has recently taken an exam and/or has come across some braindumps that have turned out to be true to share this information with the community by creating and sending VCE files. We don't say that these free VCEs sent by our members aren't reliable (experience shows that they are). But you should use your critical thinking as to what you download and memorize.
How long will I receive updates for JN0-364 Premium VCE File that I purchased?
Free updates are available during 30 days after you purchased Premium VCE file. After 30 days the file will become unavailable.
How can I get the products after purchase?
All products are available for download immediately from your Member's Area. Once you have made the payment, you will be transferred to Member's Area where you can login and download the products you have purchased to your PC or another device.
Will I be able to renew my products when they expire?
Yes, when the 30 days of your product validity are over, you have the option of renewing your expired products with a 30% discount. This can be done in your Member's Area.
Please note that you will not be able to use the product after it has expired if you don't renew it.
How often are the questions updated?
We always try to provide the latest pool of questions, Updates in the questions depend on the changes in actual pool of questions by different vendors. As soon as we know about the change in the exam question pool we try our best to update the products as fast as possible.
What is a Study Guide?
Study Guides available on Exam-Labs are built by industry professionals who have been working with IT certifications for years. Study Guides offer full coverage on exam objectives in a systematic approach. Study Guides are very useful for fresh applicants and provides background knowledge about preparation of exams.
How can I open a Study Guide?
Any study guide can be opened by an official Acrobat by Adobe or any other reader application you use.
What is a Training Course?
Training Courses we offer on Exam-Labs in video format are created and managed by IT professionals. The foundation of each course are its lectures, which can include videos, slides and text. In addition, authors can add resources and various types of practice activities, as a way to enhance the learning experience of students.
Enter Your Email Address to Proceed
Please fill out your email address below in order to purchase Certification/Exam.
Enter Your Email Address to Proceed
Please fill out your email address below in order to purchase Demo.
How It Works
Step 1. Choose Exam on Exam-Labs
Download IT Exams Questions & Answers
Step 2. Open Exam with Avanset Exam Simulator
Press here to download VCE Exam Simulator that simulates latest exam environment