Includes questions types found on actual exam such as drag and drop, simulation, type in, and fill in the blank.
Service Provider Routing and Switching, Specialist (JNCIS-SP) JN0-364 Practice Test 17
Question 160
For fictional Orion Transit, identify the shortcut that fails to address: A boundary router leaks a laboratory prefix into the provider IS-IS domain despite an approved limited export scope.
Replace explicit IS-IS export controls with a blanket accept term.
Manually configure a permanent static summary to conceal the stale LSP while topology remains wrong.
Repeatedly clear the IS-IS adjacency without determining why the computed route was not installed.
Attempt to discover another IS-IS router across the local loopback interface.
Explanation
Correct Answer
A:
That shortcut preserves the original IS-IS policy route export weakness: The IS-IS export policy does not sufficiently constrain redistributed reachable prefixes. The controlled alternative is: Apply an explicit policy permitting the intended routes and rejecting the laboratory prefix before advertisement.
Incorrect Answers
B:
The proposal recreates the separate IS-IS LSP freshness error. The current case instead concerns: A boundary router leaks a laboratory prefix into the provider IS-IS domain despite an approved limited export scope. Its specific failed assumption is: The IS-IS export policy does not sufficiently constrain redistributed reachable prefixes.
C:
This alternative is problematic for IS-IS SPF route installation, rather than the reported IS-IS policy route export. Corrective action here is: Apply an explicit policy permitting the intended routes and rejecting the laboratory prefix before advertisement.
D:
This shortcut would also be unsafe, but for a different IS-IS passive loopback case (An IS-IS loopback prefix is missing after deployment because the internal router loopback was omitted from the protocol scope.). It does not repeat the defect in this question: The IS-IS export policy does not sufficiently constrain redistributed reachable prefixes.
Question 161
At fictional Sterling Cloud (managed connectivity), this Junos network defect is reported: A junior engineer searches only show ospf neighbor when an IS-IS underlay loses a peer during maintenance. What should the specialist change first?
Configure a mutually supported level on the intended link and verify the corresponding adjacency output.
Use show isis adjacency with interface details to inspect actual peer level and state.
Parse the applicable IS-IS TLV types and lengths and validate the advertised reachability information.
Align NET area membership for Level 1 adjacency according to the provider topology plan.
Explanation
Correct Answer
B:
Correct because the observable problem is: A junior engineer searches only show ospf neighbor when an IS-IS underlay loses a peer during maintenance. Use the controlled remedy: Use show isis adjacency with interface details to inspect actual peer level and state. Confirm the resulting state with: The troubleshooting record names the IS-IS interface, peer system ID, level, and Up or Down state.
Incorrect Answers
A:
The proposal is a correction for IS-IS circuit-level mismatch, not this situation: A junior engineer searches only show ospf neighbor when an IS-IS underlay loses a peer during maintenance. Here the cause is: The operational inspection is directed at the wrong routing protocol and cannot reveal IS-IS adjacency state.
C:
That action would address the separate IS-IS TLV interpretation case, where A controller receives an IS-IS LSP but a parser treats all variable information as a fixed-format IP prefix field. The present IS-IS adjacency command selection issue instead requires: Use show isis adjacency with interface details to inspect actual peer level and state.
D:
The proposal is a correction for IS-IS NET area mismatch, not this situation: A junior engineer searches only show ospf neighbor when an IS-IS underlay loses a peer during maintenance. Here the cause is: The operational inspection is directed at the wrong routing protocol and cannot reveal IS-IS adjacency state.
Question 162
A Junos routing specialist investigates at fictional Sterling Cloud: A junior engineer searches only show ospf neighbor when an IS-IS underlay loses a peer during maintenance. What control gap requires attention?
The IS-IS export policy does not sufficiently constrain redistributed reachable prefixes.
The operational inspection is directed at the wrong routing protocol and cannot reveal IS-IS adjacency state.
The enabled IS-IS circuit levels have no common level for an adjacency to form.
IS-IS elects a DIS for a LAN pseudonode and does not use the OSPF DR and BDR election model.
Explanation
Correct Answer
B:
The scenario is explained by: The operational inspection is directed at the wrong routing protocol and cannot reveal IS-IS adjacency state. This is distinct from unrelated application failures. The recommended correction is: Use show isis adjacency with interface details to inspect actual peer level and state.
Incorrect Answers
A:
This is a different failure mechanism: The IS-IS export policy does not sufficiently constrain redistributed reachable prefixes. The current symptom is: A junior engineer searches only show ospf neighbor when an IS-IS underlay loses a peer during maintenance. The more direct defect is: The operational inspection is directed at the wrong routing protocol and cannot reveal IS-IS adjacency state.
C:
The alternate cause would explain IS-IS circuit-level mismatch. For IS-IS adjacency command selection at Sterling Cloud, the evidence instead supports: The operational inspection is directed at the wrong routing protocol and cannot reveal IS-IS adjacency state.
D:
This is a different failure mechanism: IS-IS elects a DIS for a LAN pseudonode and does not use the OSPF DR and BDR election model. The current symptom is: A junior engineer searches only show ospf neighbor when an IS-IS underlay loses a peer during maintenance. The more direct defect is: The operational inspection is directed at the wrong routing protocol and cannot reveal IS-IS adjacency state.
Question 163
Following remediation at fictional Sterling Cloud, how should the team verify that this specific issue is resolved? A junior engineer searches only show ospf neighbor when an IS-IS underlay loses a peer during maintenance.
Route selection prefers the terrestrial path under normal conditions and falls back on failure.
The troubleshooting record names the IS-IS interface, peer system ID, level, and Up or Down state.
The decoded LSP distinguishes each supported TLV and correctly presents intended prefixes or attributes.
show isis adjacency reports an Up Level 1 peer and the intended area routes appear.
Explanation
Correct Answer
B:
This outcome directly measures IS-IS adjacency command selection: The troubleshooting record names the IS-IS interface, peer system ID, level, and Up or Down state. It tests the diagnosed issue: The operational inspection is directed at the wrong routing protocol and cannot reveal IS-IS adjacency state.
Incorrect Answers
A:
That result would validate the separate IS-IS metric traffic engineering scenario (Two IS-IS paths are both reachable but the network keeps using a high-latency satellite hop rather than the engineered terrestrial route.). It does not prove the needed IS-IS adjacency command selection outcome: The troubleshooting record names the IS-IS interface, peer system ID, level, and Up or Down state.
C:
The alternative proof tests a different cause: IS-IS uses TLVs to encode diverse information, so the decoder ignores fields or misreads their lengths. The relevant acceptance condition remains: The troubleshooting record names the IS-IS interface, peer system ID, level, and Up or Down state.
D:
That result would validate the separate IS-IS NET area mismatch scenario (Two intended Level 1 IS-IS peers on the same fiber have healthy Ethernet connectivity but cannot establish a Level 1 adjacency.). It does not prove the needed IS-IS adjacency command selection outcome: The troubleshooting record names the IS-IS interface, peer system ID, level, and Up or Down state.
Question 164
After corrective implementation at fictional Sterling Cloud, reviewers revisit: A junior engineer searches only show ospf neighbor when an IS-IS underlay loses a peer during maintenance. Which safeguard best protects the repaired state?
Retest this approved Junos service-provider routing and switching control after relevant changes: show isis adjacency reports an Up Level 1 peer and the intended area routes appear.
Retest this approved Junos service-provider routing and switching control after relevant changes: The troubleshooting record names the IS-IS interface, peer system ID, level, and Up or Down state.
Retest this approved Junos service-provider routing and switching control after relevant changes: The expected active DIS originates the LAN pseudonode LSP and a new DIS is elected if it fails.
Retest this approved Junos service-provider routing and switching control after relevant changes: show isis adjacency displays the agreed Level 1 or Level 2 adjacency as Up.
Explanation
Correct Answer
B:
This periodic check is appropriate because it examines the exact prior failure at Sterling Cloud: The troubleshooting record names the IS-IS interface, peer system ID, level, and Up or Down state.
Incorrect Answers
A:
That control would prevent the different failure The router NET area addresses differ, so the peers cannot share the required Level 1 area. It would not detect recurrence of: The operational inspection is directed at the wrong routing protocol and cannot reveal IS-IS adjacency state.
C:
This recurring check measures IS-IS DIS election, whereas the fixed IS-IS adjacency command selection behavior needs ongoing evidence that: The troubleshooting record names the IS-IS interface, peer system ID, level, and Up or Down state.
D:
That control would prevent the different failure The enabled IS-IS circuit levels have no common level for an adjacency to form. It would not detect recurrence of: The operational inspection is directed at the wrong routing protocol and cannot reveal IS-IS adjacency state.
Question 165
For fictional Sterling Cloud, identify the shortcut that fails to address: A junior engineer searches only show ospf neighbor when an IS-IS underlay loses a peer during maintenance.
Repeatedly clear the IS-IS adjacency without determining why the computed route was not installed.
Reset BGP sessions because the OSPF neighbor list is empty on an IS-IS-only link.
Replace explicit IS-IS export controls with a blanket accept term.
Configure an OSPF-style BDR requirement as though it were part of IS-IS.
Explanation
Correct Answer
B:
That shortcut preserves the original IS-IS adjacency command selection weakness: The operational inspection is directed at the wrong routing protocol and cannot reveal IS-IS adjacency state. The controlled alternative is: Use show isis adjacency with interface details to inspect actual peer level and state.
Incorrect Answers
A:
This alternative is problematic for IS-IS SPF route installation, rather than the reported IS-IS adjacency command selection. Corrective action here is: Use show isis adjacency with interface details to inspect actual peer level and state.
C:
The proposal recreates the separate IS-IS policy route export error. The current case instead concerns: A junior engineer searches only show ospf neighbor when an IS-IS underlay loses a peer during maintenance. Its specific failed assumption is: The operational inspection is directed at the wrong routing protocol and cannot reveal IS-IS adjacency state.
D:
This alternative is problematic for IS-IS DIS election, rather than the reported IS-IS adjacency command selection. Corrective action here is: Use show isis adjacency with interface details to inspect actual peer level and state.
Question 166
At fictional Windward Data (private WAN), this Junos network defect is reported: An IS-IS loopback prefix is missing after deployment because the internal router loopback was omitted from the protocol scope. What should the specialist change first?
Parse the applicable IS-IS TLV types and lengths and validate the advertised reachability information.
Inspect show route protocol isis and the intended forwarding table, including hidden or inactive route reasons.
Add and verify the loopback's appropriate IS-IS reachability without creating an unnecessary physical neighbor on loopback.
Verify both interfaces support Level 2 and correct protocol reachability rather than needlessly merging area identifiers.
Explanation
Correct Answer
C:
Correct because the observable problem is: An IS-IS loopback prefix is missing after deployment because the internal router loopback was omitted from the protocol scope. Use the controlled remedy: Add and verify the loopback's appropriate IS-IS reachability without creating an unnecessary physical neighbor on loopback. Confirm the resulting state with: The loopback prefix is present in the intended IS-IS tables and remains reachable after transit link changes.
Incorrect Answers
A:
That action would address the separate IS-IS TLV interpretation case, where A controller receives an IS-IS LSP but a parser treats all variable information as a fixed-format IP prefix field. The present IS-IS passive loopback issue instead requires: Add and verify the loopback's appropriate IS-IS reachability without creating an unnecessary physical neighbor on loopback.
B:
The proposal is a correction for IS-IS SPF route installation, not this situation: An IS-IS loopback prefix is missing after deployment because the internal router loopback was omitted from the protocol scope. Here the cause is: The intended stable loopback reachability is not included in IS-IS advertisements or supporting routing policy.
D:
That action would address the separate IS-IS Level 2 interarea adjacency case, where Operators expect two Level 2 routers in different IS-IS areas to peer, but a teammate proposes giving them identical area IDs. The present IS-IS passive loopback issue instead requires: Add and verify the loopback's appropriate IS-IS reachability without creating an unnecessary physical neighbor on loopback.
Question 167
A Junos routing specialist investigates at fictional Windward Data: An IS-IS loopback prefix is missing after deployment because the internal router loopback was omitted from the protocol scope. What control gap requires attention?
The IS-IS export policy does not sufficiently constrain redistributed reachable prefixes.
The intended stable loopback reachability is not included in IS-IS advertisements or supporting routing policy.
The LSDB can be healthy while route preference, next-hop eligibility or table context prevents FIB installation.
Configured IS-IS link metrics do not reflect the intended provider path cost policy.
Explanation
Correct Answer
B:
Fictional Windward Data demonstrates this underlying defect: The intended stable loopback reachability is not included in IS-IS advertisements or supporting routing policy. Validate after remediation by checking: The loopback prefix is present in the intended IS-IS tables and remains reachable after transit link changes.
Incorrect Answers
A:
The alternate cause would explain IS-IS policy route export. For IS-IS passive loopback at Windward Data, the evidence instead supports: The intended stable loopback reachability is not included in IS-IS advertisements or supporting routing policy.
C:
That diagnosis belongs to IS-IS SPF route installation, for example: Two routers show an IS-IS adjacency Up and matching topology but an expected route remains absent from the active forwarding table. It does not explain this case, which is caused by: The intended stable loopback reachability is not included in IS-IS advertisements or supporting routing policy.
D:
The alternate cause would explain IS-IS metric traffic engineering. For IS-IS passive loopback at Windward Data, the evidence instead supports: The intended stable loopback reachability is not included in IS-IS advertisements or supporting routing policy.
Question 168
Following remediation at fictional Windward Data, how should the team verify that this specific issue is resolved? An IS-IS loopback prefix is missing after deployment because the internal router loopback was omitted from the protocol scope.
The loopback prefix is present in the intended IS-IS tables and remains reachable after transit link changes.
The Level 2 adjacency reaches Up across different intended areas and backbone routes are exchanged.
The adjacency remains Up across the tested transport condition and hold timers no longer expire prematurely.
The expected IS-IS prefix is eligible and installed in the proper RIB and forwarding table.
Explanation
Correct Answer
A:
Sign-off requires case-specific evidence: The loopback prefix is present in the intended IS-IS tables and remains reachable after transit link changes. Without that observation, the intended stable loopback reachability is not included in is-is advertisements or supporting routing policy.
Incorrect Answers
B:
That result would validate the separate IS-IS Level 2 interarea adjacency scenario (Operators expect two Level 2 routers in different IS-IS areas to peer, but a teammate proposes giving them identical area IDs.). It does not prove the needed IS-IS passive loopback outcome: The loopback prefix is present in the intended IS-IS tables and remains reachable after transit link changes.
C:
This observation is appropriate for IS-IS hello holdtime mismatch, not the IS-IS passive loopback defect at Windward Data. Verify instead: The loopback prefix is present in the intended IS-IS tables and remains reachable after transit link changes.
D:
The alternative proof tests a different cause: The LSDB can be healthy while route preference, next-hop eligibility or table context prevents FIB installation. The relevant acceptance condition remains: The loopback prefix is present in the intended IS-IS tables and remains reachable after transit link changes.
Question 169
After corrective implementation at fictional Windward Data, reviewers revisit: An IS-IS loopback prefix is missing after deployment because the internal router loopback was omitted from the protocol scope. Which safeguard best protects the repaired state?
Retest this approved Junos service-provider routing and switching control after relevant changes: show route advertising-protocol isis output excludes the lab prefix and includes sanctioned exports.
Retest this approved Junos service-provider routing and switching control after relevant changes: The troubleshooting record names the IS-IS interface, peer system ID, level, and Up or Down state.
Retest this approved Junos service-provider routing and switching control after relevant changes: All relevant peers have current LSP sequence state and the removed link no longer drives SPF selection.
Retest this approved Junos service-provider routing and switching control after relevant changes: The loopback prefix is present in the intended IS-IS tables and remains reachable after transit link changes.
Explanation
Correct Answer
D:
The repeated release test must confirm: The loopback prefix is present in the intended IS-IS tables and remains reachable after transit link changes. That check detects recurrence of the original defect: The intended stable loopback reachability is not included in IS-IS advertisements or supporting routing policy.
Incorrect Answers
A:
This recurring check measures IS-IS policy route export, whereas the fixed IS-IS passive loopback behavior needs ongoing evidence that: The loopback prefix is present in the intended IS-IS tables and remains reachable after transit link changes.
B:
That control would prevent the different failure The operational inspection is directed at the wrong routing protocol and cannot reveal IS-IS adjacency state. It would not detect recurrence of: The intended stable loopback reachability is not included in IS-IS advertisements or supporting routing policy.
C:
The proposed check belongs to the separate IS-IS LSP freshness issue at Cedar Mobile. For this case, retest: The loopback prefix is present in the intended IS-IS tables and remains reachable after transit link changes.
Question 170
For fictional Windward Data, identify the shortcut that fails to address: An IS-IS loopback prefix is missing after deployment because the internal router loopback was omitted from the protocol scope.
Assume every IS-IS TLV has the same length and carries only an IPv4 route.
Attempt to discover another IS-IS router across the local loopback interface.
Increase DIS priority despite the fact that the two peers have no common circuit level.
Configure an OSPF-style BDR requirement as though it were part of IS-IS.
Explanation
Correct Answer
B:
The proposed shortcut undermines the expected result: The loopback prefix is present in the intended IS-IS tables and remains reachable after transit link changes. The safer implementation step is: Add and verify the loopback's appropriate IS-IS reachability without creating an unnecessary physical neighbor on loopback.
Incorrect Answers
A:
The proposal recreates the separate IS-IS TLV interpretation error. The current case instead concerns: An IS-IS loopback prefix is missing after deployment because the internal router loopback was omitted from the protocol scope. Its specific failed assumption is: The intended stable loopback reachability is not included in IS-IS advertisements or supporting routing policy.
C:
This shortcut would also be unsafe, but for a different IS-IS circuit-level mismatch case (One circuit participates only in Level 1 on the remote router and only in Level 2 on the local router, preventing an adjacency.). It does not repeat the defect in this question: The intended stable loopback reachability is not included in IS-IS advertisements or supporting routing policy.
D:
The proposal recreates the separate IS-IS DIS election error. The current case instead concerns: An IS-IS loopback prefix is missing after deployment because the internal router loopback was omitted from the protocol scope. Its specific failed assumption is: The intended stable loopback reachability is not included in IS-IS advertisements or supporting routing policy.
Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-364) Practice Tests
Our team works hard to provide students with high exam practice test questions and compelling learning experiences. We're confident of the quality level of the products we offer and provide no hassle satisfaction guarantee.
Why choose Exam-Labs?613,682+Satisfied Customers since 2015
100% Latest Exam Questions
Accurate & Updated Answers
Regular Free Updates
24/7 Customer Support
Instant Download
Exam Info
Juniper JN0-364 Practice Test Questions, Juniper JN0-364 Exam Practice Test Questions
Looking to pass your tests the first time. You can study with Juniper JN0-364 certification practice test questions and answers, study guide, training courses. With Exam-Labs VCE files you can prepare with Juniper JN0-364 Service Provider Routing and Switching, Specialist (JNCIS-SP) exam practice test questions and answers. The most complete solution for passing with Juniper certification JN0-364 exam practice test questions and answers, study guide, training course.
JN0-364 Service Provider Routing and Switching, Specialist
JN0-364 is the current Service Provider Routing and Switching, Specialist exam as of October 2026. HPE Juniper Networking lists 65 multiple-choice questions in 90 minutes, Pearson VUE delivery, JNCIA-Junos as the prerequisite, and Junos OS 25.2 as the software reference. It replaced JN0-363 on February 2, 2026.
The blueprint is broad: protocol-independent routing, OSPF, IS-IS, BGP, Layer 2 bridging and VLANs, spanning-tree variants, MPLS, IPv6, GRE tunnels, and high availability. The common thread is service-provider operations. Candidates must understand not only what each protocol does but how state is configured, verified, and troubleshot across a Junos network.
The current JN0-106 associate exam provides the Junos foundation. If routing tables, policy, interface hierarchy, or operational mode are still slow, strengthen those first. JN0-364 adds enough simultaneous control planes that weak fundamentals become a major study bottleneck.
Protocol-independent routing is the control surface beneath the protocols
The blueprint includes static, aggregate, and generated routes, martian addresses, routing instances, RIB groups, load balancing, and filter-based forwarding. These are not secondary topics. They determine which tables routes enter, which paths become active, and how traffic can be steered independently of the dynamic protocol that learned a prefix.
Build labs where the same destination appears from multiple sources. Change route preference, create an aggregate, move information between routing instances, and apply filter-based forwarding. Before running a show command, predict which route should be active and why. That habit turns the routing table into a reasoned outcome rather than a display to memorize.
The concepts behind static routing make a clean baseline because they isolate local route selection before dynamic signaling complicates the picture.
OSPF and IS-IS should be practiced as living topology databases
For OSPF, JN0-364 expects knowledge of the link-state database, packet types, router IDs, neighbors, DR/BDR roles, area and router types, LSAs, configuration, policy, and troubleshooting. For IS-IS, candidates need PDUs, TLVs, levels, areas, adjacencies, DIS behavior, metrics, policy, and operational verification.
Do not study those items as vocabulary lists. Form a neighbor, inspect the database, change a metric, remove a link, and watch the shortest-path result change. Repeat the topology with the other protocol. This makes the shared link-state model visible while preserving the differences in hierarchy and protocol behavior.
The detailed explanation of OSPF areas and LSAs is useful, but a service-provider candidate should be equally comfortable reading IS-IS adjacency and database state.
BGP should be verified at every stage between peer and forwarding table
JN0-364 covers BGP messages, attributes, route selection, IBGP/EBGP interaction, peers, options, policy, and troubleshooting. A disciplined verification sequence is essential: confirm transport and session state, inspect received routes, apply policy reasoning, verify next-hop resolution, inspect active routes, and check what is advertised onward.
Create at least one lab where the BGP session remains Established while the desired route disappears. Use import policy, an unreachable next hop, or a competing path. The exercise proves why “peer up” and “service working” are different statements. The broader mechanics of BGP path selection become easier to apply when every attribute change produces visible route-state evidence.
Service-provider BGP work is inseparable from policy. Spend time writing and reading policy terms so that you can explain exactly why a route is accepted, rejected, modified, or exported.
Provider switching topics protect the service edge
The Layer 2 domain includes service-provider switching platforms, bridging concepts, frame processing, virtual switches, Q-in-Q provider bridging, VLAN port modes, tagging, IRB, and spanning-tree variants. These topics matter because service-provider networks often carry customer Layer 2 services even when the core itself is highly routed.
Practice Q-in-Q by distinguishing customer tags from the service-provider tag. Then verify how the frame is handled at ingress, across the provider domain, and at egress. This makes the separation between customer segmentation and provider forwarding explicit.
Spanning tree should be understood with security controls such as BPDU, loop, and root protection. Those features encode expectations at the edge and help prevent customer or access faults from destabilizing a larger Layer 2 domain.
MPLS study should begin with packet forwarding before signaling
The current blueprint includes MPLS terminology, label headers, end-to-end forwarding, label information, routing-table relationships, RSVP, LDP, and segment routing with MPLS. Start with the dataplane. Trace how an ingress node pushes a label, how transit nodes swap it, and how the egress processes the final label.
Then attach each signaling method to the label-switched path it creates. LDP distributes labels along routing paths, RSVP can establish traffic-engineered paths, and segment routing expresses path intent through segments. The concepts in MPLS forwarding provide a strong base when paired with Junos route and label-table output.
Do not memorize labels as static numbers. Focus on the control information that creates them and the forwarding behavior they enable. That perspective scales into VPN and traffic-engineering work at the professional level.
When comparing MPLS control methods, keep one question in view: what information tells the router which labeled path to use? LDP generally couples label distribution to IGP reachability, RSVP can signal traffic-engineered LSPs with explicit constraints, and segment routing represents path intent through ordered segments. Practice reading the resulting state rather than memorizing a feature table. If an LSP is down, determine whether the missing evidence is an IGP route, a signaling relationship, a label binding, or the forwarding entry itself.
Troubleshooting should therefore move from dependency to dependent feature. Verify core addressing and IGP reachability first, then protocol sessions, then label or tunnel state, and finally end-to-end service traffic. This sequence is efficient because later layers cannot be healthy when their transport assumptions are false. It also mirrors real service-provider operations, where the fastest resolution often comes from proving the lowest broken dependency before touching policy or service configuration.
IPv6 belongs in the same routing model as IPv4
JN0-364 covers IPv6 static routing and dynamic routing through OSPFv3, IS-IS, and BGP, plus IPv6-over-IPv4 tunneling. Treat IPv6 as a routed protocol with its own addressing and neighbor behavior rather than as a separate specialty. Route selection, policy, protocol adjacency, and troubleshooting discipline still apply.
Build dual-stack labs so you can compare the same topology under both address families. Verify that a protocol session can be healthy for one family while reachability for another is absent. This teaches you to inspect family-specific route state instead of assuming that one working path proves the other.
For transition tunnels, explicitly trace the outer IPv4 path and the inner IPv6 packet. The layered model is the same one used for GRE and prevents confusion about which address family is failing.
GRE tunnels add reachability without removing underlay dependencies
The tunnel objective covers applications, design considerations, GRE configuration, and troubleshooting. A GRE interface can make two remote networks appear directly connected at the logical layer, but the outer endpoints still depend on ordinary routing. If the underlay cannot reach the tunnel destination, the overlay path cannot work.
In the lab, verify outer routes, tunnel source and destination, inner routing, and MTU. Then break each independently. The difference between an underlay failure and an inner-route problem becomes obvious when you compare packet captures and interface state.
Use the conceptual discussion of GRE tunneling to broaden understanding, while keeping configuration practice aligned to the exact JN0-364 objectives.
High availability combines fast detection with preserved forwarding
Current HA topics include LAG, graceful restart, GRES, NSB, NSR, BFD, and VRRP. Each protects a different part of service continuity. Link aggregation addresses physical path loss, BFD accelerates failure detection, graceful and nonstop mechanisms reduce control-plane disruption, and VRRP protects the first-hop gateway identity.
Build a table that states for each feature what fails, what detects the failure, what state is preserved, and what alternate path or node takes over. The principles of VRRP redundancy are especially useful when contrasted with BFD: one provides a virtual gateway role, the other supplies rapid liveness information.
In testing, record packets lost and convergence time. A protocol can be “working as designed” while still failing a service-level objective if recovery is too slow for the application.
Study the current exam as one service-provider system
Separate notebooks for OSPF, BGP, MPLS, and HA are useful early, but final preparation should combine them. Build a topology where an IGP supplies core reachability, MPLS uses that underlay, BGP carries service or external routes, and HA mechanisms protect critical paths. Then introduce a fault and decide which control plane should react.
Use the objective list as a four-part readiness matrix: explain, configure, verify, troubleshoot. If you can define a feature but cannot identify healthy operational output, the topic is incomplete. If you can configure it but cannot predict the effect of a failure, it is not yet specialist-level knowledge.
The current professional progression represented in the approved inventory is JN0-664. That path rewards candidates who build durable service-provider reasoning now, because advanced Layer 2 VPN, EVPN, MPLS, and policy work assumes the specialist foundation is already fluent.
Before scheduling, verify the live JN0-364 blueprint and software reference again. The certification program's branding changed under HPE Networking in September 2026, but the exam remains centered on Junos service-provider routing and switching. Use current first-party objectives for scope and let hands-on operational evidence—routes, adjacencies, labels, policy results, tunnel state, and failover behavior—drive the final review.
Use Juniper JN0-364 certification exam practice test questions, study guide and training course - the complete package at discounted price. Pass with JN0-364 Service Provider Routing and Switching, Specialist (JNCIS-SP) practice test questions and answers, study guide, complete training course especially formatted in VCE files. Latest Juniper certification JN0-364 exam practice test questions and answers will guarantee your success without studying for endless hours.
FAQs
Juniper JN0-364 Exam Practice Test Questions, Juniper JN0-364 Practice Test Questions and Answers
Do you have questions about our JN0-364 Service Provider Routing and Switching, Specialist (JNCIS-SP) practice test questions and answers or any of our products? If you are not clear about our Juniper JN0-364 exam practice test questions, you can read the FAQ below.
The JN0-364 Premium File has been developed by industry professionals, who have been working with IT certifications for years and have close ties with IT certification vendors and holders - with most recent exam questions and valid answers.
JN0-364 Premium File is presented in VCE format. VCE (Virtual CertExam) is a file format that realistically simulates JN0-364 exam environment, allowing for the most convenient exam preparation you can get - in the convenience of your own home or on the go. If you have ever seen IT exam simulations, chances are, they were in the VCE format.
What is VCE?
VCE is a file format associated with Visual CertExam Software. This format and software are widely used for creating tests for IT certifications. To create and open VCE files, you will need to purchase, download and install VCE Exam Simulator on your computer.
Can I try it for free?
Yes, you can. Look through free VCE files section and download any file you choose absolutely free.
Where do I get VCE Exam Simulator?
VCE Exam Simulator can be purchased from its developer, https://www.avanset.com. Please note that Exam-Labs does not sell or support this software. Should you have any questions or concerns about using this product, please contact Avanset support team directly.
How are Premium VCE files different from Free VCE files?
Premium VCE files have been developed by industry professionals, who have been working with IT certifications for years and have close ties with IT certification vendors and holders - with most recent exam questions and some insider information.
Free VCE files All files are sent by Exam-labs community members. We encourage everyone who has recently taken an exam and/or has come across some braindumps that have turned out to be true to share this information with the community by creating and sending VCE files. We don't say that these free VCEs sent by our members aren't reliable (experience shows that they are). But you should use your critical thinking as to what you download and memorize.
How long will I receive updates for JN0-364 Premium VCE File that I purchased?
Free updates are available during 30 days after you purchased Premium VCE file. After 30 days the file will become unavailable.
How can I get the products after purchase?
All products are available for download immediately from your Member's Area. Once you have made the payment, you will be transferred to Member's Area where you can login and download the products you have purchased to your PC or another device.
Will I be able to renew my products when they expire?
Yes, when the 30 days of your product validity are over, you have the option of renewing your expired products with a 30% discount. This can be done in your Member's Area.
Please note that you will not be able to use the product after it has expired if you don't renew it.
How often are the questions updated?
We always try to provide the latest pool of questions, Updates in the questions depend on the changes in actual pool of questions by different vendors. As soon as we know about the change in the exam question pool we try our best to update the products as fast as possible.
What is a Study Guide?
Study Guides available on Exam-Labs are built by industry professionals who have been working with IT certifications for years. Study Guides offer full coverage on exam objectives in a systematic approach. Study Guides are very useful for fresh applicants and provides background knowledge about preparation of exams.
How can I open a Study Guide?
Any study guide can be opened by an official Acrobat by Adobe or any other reader application you use.
What is a Training Course?
Training Courses we offer on Exam-Labs in video format are created and managed by IT professionals. The foundation of each course are its lectures, which can include videos, slides and text. In addition, authors can add resources and various types of practice activities, as a way to enhance the learning experience of students.
Enter Your Email Address to Proceed
Please fill out your email address below in order to purchase Certification/Exam.
Enter Your Email Address to Proceed
Please fill out your email address below in order to purchase Demo.
How It Works
Step 1. Choose Exam on Exam-Labs
Download IT Exams Questions & Answers
Step 2. Open Exam with Avanset Exam Simulator
Press here to download VCE Exam Simulator that simulates latest exam environment