Limited Time Discount Offer
30% Off - Ends in 02:00:00

X

HP HP3-C29 Dumps

HP
HP LaserJet Enterprise M4555 MFP
HP
HP LaserJet Enterprise M4555 MFP

Questions & Answers for HP HP3-C29

Showing 1-15 of 25 Questions

Question #1

You have powered on the HP LaserJet Enterprise M4555 MFP after replacing the
encrypted hard drive, but the product will not boot up to a Ready state What is the first
thing you should do?

A. Replace the encrypted hard drive again

B. Run a Cold Reset from the pre-boot menu

C. Remove and replace the formatter board

D. Verify that the latest firmware has been downloaded on the replacement hard drive

Question #2

The HP Universal Print Driver (UPD) can be installed in which modes?

A. Discrete or universal mode

B. Stationary or mobile mode

C. Traditional or dynamic mode

D. Specific or generic mode

Reference:http://h20331.www2.hp.com/Hpsub/downloads/UPD5_guide_final,%20web.pdf(
page 4, first sentence on the page)

Question #3

On the HP LaserJet Enterprise M4555 MFR firmware is stored on which component(s)?

A. The encrypted hard disk or solid state drive

B. DIMM memory

C. The DC Controller and the ICB

D. The formatter

Question #4

Which of the HP LaserJet Enterprise M4555 MFP bundles does NOT feature automatic
duplexing?

A. HP M4555

B. HP M4555F

C. HP M4555LN

D. HP M4555SKM

Question #5

The HP LaserJet Enterprise M4555 MFP allows for how much memory expansion through
available DIMM slots on the formatter?

A. 16MB

B. 64MB

C. 256MB

D. 1280 MB

Reference:http://www.hp.com/hpinfo/newsroom/press_kits/2011/businessprinting2011/HP_
LaserJet_Enterprise_M4555.pdf(page 2, see bullet # 13)

Question #6

Which feature allows the fuser in the HP LaserJet Enterprise M4555 MFP to heat up to
optimum temperature from Sleep mode almost immediately?

A. A quick-heating ceramic element is used instead of a lamp.

B. Reflective shielding is installed, which reduces the amount of heat that is wasted.

C. The dual-element corona wire uses both elements for quick heating, and then resumes single-element use for fusing.

D. A reduced-capacity heating charge is retained while in Sleep mode

Reference:http://www.computersuppliesultd.com/Peripherals/ce738a.pdf(see more energy
efficient)

Question #7

Why is the Hardware Integration Pocket included on the HP LaserJet Enterprise M4555
MFP?

A. One unopened ream of paper can be stored in the Hardware Integration Pocket for quick retrieval when needed.

B. It allows administrators to connect third-party solutions directly to the control panel.

C. The Hardware Integration Pocket displays the current status of all the integrated hardware of the device.

D. The Hardware Integration Pocket contains a USB port that administrators can use to add third-party solutions.

Reference:http://www.imageoneway.com/pdfs/4555mfp.pdf(page 5, bulleted # 3)

Question #8

Which of the HP LaserJet Enterprise M4555 MFP bundles does NOT include fax
capabilities at time of purchase?

A. M4555h

B. M4555

C. M4555F

D. M4555SKM

Reference:http://www.hp.com/hpinfo/newsroom/press_kits/2011/businessprinting2011/HP_
LaserJet_Enterprise_M4555.pdf(page 2, see the series at a glance)

Question #9

Why must customers perform a remote firmware upgrade (RFU) after replacing the
encrypted hard drive or the solid state drive?

A. The replacement encrypted hard drive and solid state drive ship without firmware. The latest version of firmware must be loaded on them after installation.

B. The firmware on the printer must be upgraded to match the firmware version on the replacement encrypted hard drive or solid state drive.

C. The USB control panel will not recognize the replacement encrypted hard drive or solid state drive until the device firmware is updated.

D. All replacement encrypted hard drives and solid state drives contain product-introduction firmware, which must be upgraded during installation.

Question #10

Which statement is true about the HP LaserJet Enterprise M4555 MFP HP High
Performance Secure Hard Disk?

A. The encrypted hard disk contents are deleted if a device Cold Reset is performed.

B. The encrypted hard disk is physically locked to the device using a Drive Lock Key.

C. The encrypted hard disk contents become unreadable if the disk is removed from the device.

D. The encrypted hard disk must only be installed by a qualified HP service technician.

Question #11

What happens if the HP 3-bin Stapling Mailbox is removed and then re-attached without
powering off the MFP?

A. The device powers off automatically.

B. A print engine firmware error occurs.

C. The device enters a Ready state.

D. The device will not power on.

Question #12

What is the function of the Driver Deployment Utility (DDL))?

A. It acts as a utility to provide Windows 7 support for all HP printer drivers.

B. It allows the PCL 6 driver and the Universal Print Driver (UPD) to be installed on the same device.

C. It enables the printer driver to be configured through the device Embedded Web Server (EWS).

D. It allows an administrator to create a printer driver install package for unattended installation.

Reference:https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=4&ved=0
CEcQFjAD&url=ftp%3A%2F%2Fftp.comp-
sol.com%2FTJ%2FHP_cp2025%2FWindows_7__64-
bit%2FHP_Printer_Adminstrator_Resource_Kit%2Fv1.5__2011_10_31%2Fpark-
v1.5%2Fdriver%2520deployment%2520utility%2FRelease%2520Notes-
ddu.doc&ei=1bQYUrnNBI2PswbZv4HQCg&usg=AFQjCNHAmkT6qUYpK4fA-
dy4IWcnAcUURQ&sig2=b1JmZUzowa-tEVJYogxx-Q&bvm=bv.51156542,d.Yms

Question #13

How many external USB host ports does the HP LaserJet Enterprise M4555 MFP have?

A. 0

B. 1

C. 2

D. 3

Reference:http://www.hp.com/hpinfo/newsroom/press_kits/2011/businessprinting2011/HP_
LaserJet_Enterprise_M4555.pdf

Question #14

What is true about the HP LaserJet Enterprise M4555 MFP control panel?

A. It features a USB port on the side for adding third-party solutions.

B. It is a touchscreen color display.

C. It features a built-in control-panel diagnostic utility.

D. It features a text-to-speech accessibility option (English only)

Reference:http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?objectID=c
02809988&prodSeriesId=4072931

Question #15

A customer complains that copy jobs using the ADF have lines on the output, but copy jobs
from the flatbed look fine. What is the most likely reason this is occurring?

A. The ADF rollers are not rotating at a consistent speed

B. One or more of the LEDs used for ADF copying have stopped working.

C. The scanner is not in the correct location for ADF scanning.

D. A small amount of dirt or a smudge is on the ADF glass.

×